#1
|
|||
|
|||
![]()
Here is the brand new Orange "Bright Box", manufactured by "Astoria Networks" (whoever they are) only released this week.
http://help.orange.co.uk/orangeuk/su...ireless-router Here is mine, taken apart and photographed: http://www.flickr.com/photos/2200869...7629056125153/ This little box is amazingly fast, with a 320Mhz CPU and 64Mb ram! There is a brilliant USB sharing/NAS feature built it, also (see screenshot attached), with configurable users etc. 4-PIN header pinout (it's called "J3" on the PCB): ================================ [o o o o] "J3" 1 2 3 ^---- unmarked (GROUND) 1: Not connected 2: Tx data (connect to Rx on PC) 3: Rx data (connect to Tx on PC) (4): [unlabelled] GROUND ================================ I just attached my PL-2303 USB to serial converter, found ground, Tx & Rx, and powered the little beauty on. Here is the boot log (there is a 4-pin header inside... how convenient for me): BOOT LOG: Code:
HELO CPUI L1CI DRAM ---- PHYS ZQDN PHYE DINT LSYN USYN MSYN LMBE PASS ---- ZBSS CODE DATA L12F ROMM ==== HELO ZBSS RAMM ==== Copyright (C) 2011 Arcadyan Technology. SPIFLASH: JEDEC ID: 0xc22017, size: 8192KB block: 64KB(64), sector: 4KB(1024) NVRAM(0) MAGIC checking passed! NVRAM(0) CRC checking passed! total 7 of NVRAM(0) entries loaded NVRAM(1) MAGIC checking passed! NVRAM(1) CRC checking passed! total 7 of NVRAM(1) entries loaded BOOTLOADER version 1.0.9 for BrightBox Build Date: Wed Nov 9 10:21:21 2011 (glen_lin@buildbed) Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz Memory Test Passed! Total Memory: 67108864 bytes (64MB) HW Version: 01 Board IP address 192.168.1.1 Board IP netmask 255.255.255.0 Gateway IP address 0.0.0.0 Server IP address 192.168.1.99 Boot image (1 or 2) 1 MAC address number 1 MAC address base 74-31-70-B5-A3-7C *** Press any key to stop auto run (3 seconds) *** Auto run second count down: 0 Loading primary image ... Finished loading 8257536 bytes DATE : Mon Nov 28 17:30:50 2011 VER : v0.09.82.0001 CRC : 3C15DF56 Code Address: 0x80002000, Entry Address: 0x801d8520 Decompression OK! Entry at 0x801d8520 Starting program at 0x801d8520 Linux version 2.6.30 (glen_lin@buildbed) (gcc version 4.1.2) #1 Mon Nov 28 17:16:00 CST 2011 Detected Broadcom 0x6328 CPU revision 10b0 CPU frequency is 320 MHz 64MB of RAM installed registering 32 GPIOs console [early0] enabled CPU revision is: 0002a075 (Broadcom BCM63281) board_bcm9632x: board name: AR7516AAW Determined physical RAM map: memory: 03f00000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00003f00 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00003f00 On node 0 totalpages: 16128 free_area_init_node: node 0, pgdat 8024bb30, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 94 pages used for memmap Normal zone: 11938 pages, LIFO batch:1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16002 Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro rootfstype=squashfs wait instruction: enabled Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes NR_IRQS:80 PID hash table entries: 256 (order: 8, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 61368k/64512k available (1912k kernel code, 3124k reserved, 436k data, 120k init, 0k highmem) Calibrating delay loop... 318.46 BogoMIPS (lpj=159232) Mount-cache hash table entries: 512 --Kernel Config-- SMP=0 PREEMPT=0 DEBUG_SPINLOCK=0 DEBUG_MUTEXES=0 net_namespace: 536 bytes /proc/net/netfilter/nf_cli_bw_mon created NET: Registered protocol family 16 registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 pci 0000:00:00.0: PME# supported from D0 D3hot pci 0000:00:00.0: PME# disabled pci 0000:01:00.0: reg 10 64bit mmio: [0x000000-0x003fff] pci 0000:01:00.0: supports D1 D2 pci 0000:00:00.0: PCI bridge, secondary bus 0000:01 pci 0000:00:00.0: IO window: disabled pci 0000:00:00.0: MEM window: 0x10f00000-0x10ffffff pci 0000:00:00.0: PREFETCH window: disabled PCI: Enabling device 0000:00:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:00.0 to 64 BLOG v3.0 Initialized BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 Nov 28 2011 17:14:06 initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 Total # RxBds=848 bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 119 io scheduler noop registered (default) PCI: Setting latency timer of device 0000:00:00.0 to 64 aer 0000:00:00.0:pcie02: service driver aer loaded bcm632x-uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm632x-uart console handover: boot [early0] -> real [ttyS0] loop: module loaded PPP generic driver version 2.4.2 NET: Registered protocol family 24 PPPoL2TP kernel driver, V1.0 m25p80 spi0.0: mx25l6405d (8192 Kbytes) Creating 6 MTD partitions on "spi0.0": 0x00000000e000-0x00000000f000 : "manuf" 0x00000000f000-0x000000010000 : "nvram" 0x000000110000-0x0000007f0000 : "rootfs" 0x000000010000-0x0000007f0000 : "priimg" 0x0000007f0000-0x000000800000 : "pricfg" 0x000000000000-0x00000000e000 : "bootldr" bcm632x-hsspi bcm632x-hsspi.0: at 0xb0001000 (irq 37, FIFOs size 510) v1.0 Registered led device: dsl:sync Registered led device: dsl:data Registered led device: wps:green Registered led device: sys:a Registered led device: sys:b Registered led device: sys:c Registered led device: sys:d GACT probability on u32 classifier Actions configured TCP cubic registered NET: Registered protocol family 17 Bridge firewalling registered Initializing MCPD Module 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:2. Freeing unused kernel memory: 120k freed gpio-buttons driver version 0.1.2 input: gpio-buttons as /devices/platform/gpio-buttons/input/input0 Button Hotplug driver version 0.4.1 arc_oshal: module license 'Propritary' taints kernel. Disabling lock debugging due to kernel taint oshal_init(1066) DRV: Created Successfully ARC_KERNEL_OSIX_init(396) DRV: Created Successfully Broadcom Logger v0.1 Nov 28 2011 17:16:27 Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Nov 28 2011 17:16:29 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Nov 28 2011 17:16:29 Broadcom BCM6328B0 Ethernet Network Device v0.1 Nov 28 2011 17:16:31 ETH Init: Ch:0 - 180 tx BDs at 0xa3946000 ETH Init: Ch:0 - 400 rx BDs at 0xa3a21000 bcm632x-dg: register bcmsw eth0: MAC Address: 74:31:70:B5:A3:7C eth1: MAC Address: 74:31:70:B5:A3:7C eth2: MAC Address: 74:31:70:B5:A3:7C eth3: MAC Address: 74:31:70:B5:A3:7C Broadcom 802.1Q VLAN Interface, v0.1 bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.4 Nov 28 2011 17:16:44 bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom Power Management v0.1 Nov 28 2011 17:18:42 Broadcom WLAN configuration service start PCI: Enabling device 0000:01:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:01:00.0 to 64 wl: passivemode=1 wl: napimode=0 wl: allocskbmode=1 wl:force using embedded data wlc_bmac_attach(2582): BpGetWirelessFlags NIY! wl0: Broadcom BCMa8dc 802.11 Wireless Controller 5.100.96.0.cpe4.10L01a.8 bcm632x-dg: register wl0 ip_tables: (C) 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (1008 buckets, 4032 max) ctnetlink v0.93: registering with nfnetlink. xt_time: kernel timezone is -0000 IMQ driver loaded successfully. Hooking IMQ after NAT on PREROUTING. Hooking IMQ before NAT on POSTROUTING. Osix_service_sys_cmd_thread_main[1302]: Osix Wait for Batch System Comand Processing... Osix Thread service system command started successfully ! ramdisk/etc/config/ ramdisk/etc/config/backup.bin ramdisk/etc/config/glbcfg.save MHDL_DB_WLAN_Init_Setting[118] MHDL_DB_LAN_Init_Setting[525] Password for 'admin' changed BcmAdsl_Initialize=0xC040AEF8, g_pFnNotifyCallback=0xC04C08D4 BcmAdsl_Initialize(202): BpGetRj11InnerOuterPairGpios NIY pSdramPHY=0xA3FFFFF8, 0xD11BD1AB 0xD99AD3DB *** PhySdramSize got adjusted: 0x82CDC => 0x98878 *** AdslCoreSharedMemInit: shareMemAvailable=423776 AdslCoreHwReset: pLocSbSta=83120000 bkupThreshold=1600 AdslCoreHwReset: AdslOemDataAddr = 0xA3F77D28 EXECUTE "/bin/util_xdsl_cli mode auto" BcmAdsl_Initialize=0xC040AEF8, g_pFnNotifyCallback=0xC04C08D4 EXECUTE "/bin/util_xdsl_cli bitswap enable" BcmAdsl_Initialize=0xC040AEF8, g_pFnNotifyCallback=0xC04C08D4 EXECUTE "/bin/util_xdsl_cli sra enable" BcmAdsl_Initialize=0xC040AEF8, g_pFnNotifyCallback=0xC04C08D4 devCtl_xtmInitiaXTM Init: Ch:0 - 400 rx BDs at 0xa3bc5000 lize(174): devCtXTM Init: Ch:1 - 16 rx BDs at 0xa29ad780 l_getSdramSize NIY! WAN Type is ADSL Success Success Success Success Success Success Power ON stage, no need to delete interface in advance. ioctl failed. check if wl0.1 exists MHDL_DB_SYS_DNS_UPDATE_RESOLV_CONF[1046]: cmd_buf (cp /tmp/tmpResolv_536.conf /etc/resolv.conf) dhcp IP compare: old () vs new (192.168.1.101). dhcp lease time compare: old (00000000) vs new (0002A300). mhdl_dn_lan_dhcpd_cfg_file_init[169]: Check_IP_Changed : (TRUE). Lease_Time_Changed (TRUE) dhcp IP compare: old () vs new (192.168.2.1). dhcp lease time compare: old (00000000) vs new (0000A8C0). mhdl_dn_lan_dhcpd_cfg_file_init[169]: Check_IP_Changed : (TRUE). Lease_Time_Changed (TRUE) dhcp IP compare: old () vs new (192.168.3.1). Restart Level is BR0_IPCHANGED BR0 IP Changed dhcp lease time compare: old (00000000) vs new (0000A8C0). mhdl_dn_lan_dhcpd_cfg_file_init[169]: Check_IP_Changed : (TRUE). Lease_Time_Changed (TRUE) Initializing WAN ioctl failed. check if wl0.1 exists XTM driver returns Not Found Error bcmxtmrt: MAC address: 74 31 70 b5 a3 7e [DoCreateDeviceReq.2998]: register_netdev [DoCreateDeviceReq.3000]: register_netdev done /bin/bcm_atmctl operate conn --add 1.0.38 aal5 vcmux_pppoa 1MHDL_DB_SYS_STOP_UPNPD[1322]: cmd (killall arc_upnp) killall: arc_upnp: no process killed MHDL_DB_SYS_RESTART_UPNPD[1306]: cmd_buf: /usr/sbin/arc_upnp & Success EXECUTE "/bin/pppd -c pppoa1 -a atm0.0.0.38 -H -k -R 30 -K 60 -M 1492 -u readytoconnect@fs -p mistyview &" Success Success Success Success ioctl failed. check if wl0.1 exists PPP: pppoa1 Start to connect ... netdev path : pppoa1 -> atm0 modprobe: can't open 'modules.dep': No such file or directory The kernel doesn't support the ebtables 'nat' table. ioctl failed. check if wl0.1 exists iptables v1.4.8: Couldn't find target `QOSUP' Try `iptables -h' or 'iptables --help' for more information. iptables v1.4.8: Couldn't find target `QOSUP' Try `iptables -h' or 'iptables --help' for more information. net.netfilter.nf_conntrack_acct = 1 ioctl failed. check if wl0.1 exists RTNETLINK answers: Invalid argument CLOCK_MONOTONIC, resolution=0.999848 System clock_res=999848, clock_hz=1000 config_httpd(517) LAN IP Address (192.168.1.101) Pre-init before any Application was started. config_httpd(526) LAN IP Mask (255.255.255.0) httpd: after config_httpd() httpd: listen at 192.168.1.101:5438 [HTTPD] httpd_main(): Not the 1st httpd_main task killall: dyndns: no process killed killall: tzoupdate: no process killed start httpd Success Success Success SSDP_SetRCVSocket(217): Recv SsdpSock 14 Success Success QueryEthernetLinkStatus[115]: WAN Interface Name (NULL) Port Number: eth3, PortStatus: 0 killall: bcm_mcpd: no process killed ioctl failed. check if wl0.1 exists killall arc_httpd start arc_httpd lease_init[65]: /etc/udhcpd/udhcpd_001.leases ! 1 Jan 00:00:27 sntp[982]: kod_init_kod_db(): Cannot open KoD db file /var/db/ntp-kod 1 Jan 00:00:27 sntp[982]: Error looking up (A) ntp.readytoconnect.co.uk: Name or service not known Unable to resolve hostname(s) HTTPD: main(1478) Restart Level is BR1_IPCHANGED BR1 IP Changed main(1570): I am child for HTTPD SVR 2 main(1582): Start HTTPD SVR 0 ioctl failed. check if wl0.1 exists killall: bcm_mcpd: no process killed lease_init[65]: /etc/udhcpd/udhcpd_002.leases ! Restart Level is BR2_IPCHANGED BR2 IP Changed please assign value for wl0.1_ssid please assign value for wl0.2_ssid killall: bcm_mcpd: no process killed iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. ioctl failed. check if wl0.1 exists iptables: No chain/target/match by that name. conntrack v1.0.0 (conntrack-tools): connection tracking table has been emptied. conntrack v1.0.0 (conntrack-tools): expectation table has been emptied. ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists rmmod: can't unload 'nf_nat_pt': unknown symbol in module, or unknown parameter ioctl failed. check if wl0.1 exists killall: urlfilterd: no process killed ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists conntrack v1.0.0 (conntrack-tools): connection tracking table has been emptied. conntrack v1.0.0 (conntrack-tools): expectation table has been emptied. ioctl failed. check if wl0.1 exists please assign value for wl0_radius_key please assign value for wl0_nas_id 1 Jan 00:00:50 sntp[2769]: Error looking up (A) ntp.readytoconnect.co.uk: Name or service not known Unable to resolve hostname(s) ioctl failed. check if wl0.1 exists please assign value for wl0.1_wpa_psk please assign value for wl0.2_wpa_psk start WLAN manager WLmngr Daemon is running ioctl failed. check if wl0.1 exists ifconfig: wl0.1: error fetching interface information: Device not found ifconfig: wl0.2: error fetching interface information: Device not found wlevt_init@157: opened loopback socket 6 wlevt is ready for new msg... nvram_commit NIY! ifconfig: wl0.1: error fetching interface information: Device not found ifconfig: wl0.2: error fetching interface information: Device not found ioctl failed. check if wl0.1 exists >>>>>Start Auto Channel search !!! >>>>> Setting SSID: "BrightBox-rc3bq3" Setting SSID: "ar7516aaw-guest" Setting SSID: "ar7516aaw-guest2" PPP: pppoa1 Start to connect ... netdev path : pppoa1 -> atm0 chanspec 0x2b01 selected bcm_wlctl: Unsupported bcm_wlctl: Not Permitted bcm_wlctl: Undefined error nvram_commit NIY! LLTD daemon is ready to run EAP daemon is ready to run NAS daemon is ready to run wlmngr_startWsc(1125): wait for WPSUI message timeout! dalQos_setDefaultWlQueuesLock NIY! dalQos_setDefaultWlQueuesLock NIY! dalQos_setDefaultWlQueuesLock NIY! read/write to TR69 configuration NIY! Starting to init bandwidth contrl of wifi!! /sbin/tctrl qdisc del dev wl0 ingress 2>/dev/null /usr/sbin/ebtables -X wl0_egress 2>/dev/null iptables: No chain/target/match by that name. /sbin/tctrl qdisc del dev wl0 root 2>/dev/null /usr/sbin/ebtables -X wl0_ingress 2>/dev/null /sbin/tctrl qdisc del dev wl0.1 ingress 2>/dev/null /usr/sbin/ebtables -X wl0.1_egress 2>/dev/null /sbin/tctrl qdisc del dev wl0.1 root 2>/dev/null /usr/sbin/ebtables -X wl0.1_ingress 2>/dev/null /sbin/tctrl qdisc del dev wl0.2 ingress 2>/dev/null /usr/sbin/ebtables -X wl0.2_egress 2>/dev/null /sbin/tctrl qdisc del dev wl0.2 root 2>/dev/null /usr/sbin/ebtables -X wl0.2_ingress 2>/dev/null start mcpd 1 Jan 00:01:15 sntp[3572]: Error looking up (A) ntp.readytoconnect.co.uk: Name or service not known Unable to resolve hostname(s) start USB service Password for 'user' changed Password for 'matt' changed bcm632x-usb-ohci bcm632x-usb-ohci.0: init err (c8300000 0000) bcm632x-usb-ohci bcm632x-usb-ohci.0: startup error -79 bcm632x-usb-ohci: probe of bcm632x-usb-ohci.0 failed with error -79 action name is add product name is 1d6b/2/206 Driver 'sd' needs updating - please use bus_type methods start UMTS service action name is add product name is 1d6b/2/206 start Power-Management service Host MIPS Clock divider pwrsaving is enabled DDR Self Refresh pwrsaving is enabled System Start with Normal Phase root@BrightBox:/ # Code:
root@BrightBox:/home/default # cat /proc/cpuinfo system type : bcm632x/AR7516AAW (0x6328/0x10B0) processor : 0 cpu model : Broadcom BCM63281 V7.5 BogoMIPS : 318.46 wait instruction : yes microsecond timers : yes tlb_entries : 32 extra interrupt vector : no hardware watchpoint : no ASEs implemented : shadow register sets : 1 core : 0 VCED exceptions : not available VCEI exceptions : not available unaligned exceptions : 114 Code:
root@BrightBox:/home/default # cat /proc/meminfo MemTotal: 61508 kB MemFree: 30200 kB Buffers: 3656 kB Cached: 11844 kB SwapCached: 0 kB Active: 7200 kB Inactive: 11308 kB Active(anon): 3008 kB Inactive(anon): 0 kB Active(file): 4192 kB Inactive(file): 11308 kB SwapTotal: 0 kB SwapFree: 0 kB Dirty: 0 kB Writeback: 0 kB AnonPages: 3016 kB Mapped: 1944 kB Slab: 6824 kB SReclaimable: 836 kB SUnreclaim: 5988 kB PageTables: 312 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 30752 kB Committed_AS: 6204 kB VmallocTotal: 1032148 kB VmallocUsed: 5416 kB VmallocChunk: 990548 kB Code:
Linux version 2.6.30 (glen_lin@buildbed) (gcc version 4.1.2) #1 Mon Nov 28 17:16:00 CST 2011 Code:
root@BrightBox:/proc # cat mtd dev: size erasesize name mtd0: 00001000 00001000 "manuf" mtd1: 00001000 00001000 "nvram" mtd2: 006e0000 00001000 "rootfs" mtd3: 007e0000 00001000 "priimg" mtd4: 00010000 00001000 "pricfg" mtd5: 0000e000 00001000 "bootldr" Will update when more info available... Last edited by unlokia; 27-January-2012 at 20:12. |
#2
|
|||
|
|||
![]()
I just made a backup of the /dev/mtdX devices (all) and ZIPped it, and uploaded to Rapidshare. The command syntax I used was
Code:
cat /dev/mtdX > filename Where the "X" in "mtdX" is the number of the partition, and "filename" is the output file: https://rapidshare.com/files/1946813...htBox_MTDs.zip MOBILE BROADBAND FUNCTIONALITY Also, it appears this router has been designed to work with USB mobile broadband dongles as well, so that you can broadcast your mobile broadband, when the dongle is in the USB port. Apparently it is in "Beta", but it's a good feature! ![]() Here is a "usb_modeswitch" script of some sort, which pertains to aforementioned Mobile broadband dongles: Code:
root@BrightBox:/etc/hotplug.d/3g # cat umts_modes_switch_for_3g.sh #!/bin/sh echo "action name is ${ACTION}" > /dev/console echo "product name is ${PRODUCT}" > /dev/console case "$ACTION" in remove) if [ -e /tmp/3g_out_times ] ; then echo "remove usb second times" > /dev/console else touch /tmp/3g_out_times # echo hotplug umts > /dev/console # echo action @${ACTION} > /dev/console # echo subsystem @${SUBSYSTEM} > /dev/console # echo physdevpath @${PHYSDEVPATH} > /dev/console # echo devpath @${DEVPATH} > /dev/console # echo modalias @${MODALIAS} > /dev/console # echo major @${MAJOR} > /dev/console # echo minor @${MINOR} > /dev/console # echo devicename @${DEVICENAME} > /dev/console # for real 3G dongle, not storage remove.... case "${PRODUCT}" in "12d1/141b/0") echo "E175x Series 3G card out (E1750/Eg i=0 while [ "$i" != "5" ] do i=$(($i+1)) sleep 1 if [ ! -e /tmp/read_lock_3g_dogn i=5 fi done rm -f /tmp/3g_in_times rm -f /tmp/3g_umts_mode_switch_done rm -f /tmp/3g_pppd_dial_up_ready rm -f /dev/ttyUSB* rm -f /tmp/3g_dongle_ready_in_times rm -f /tmp/arc_3g_dongle_product_info.tt /usr/sbin/sh_3g_stop.sh rm -f /tmp/read_lock_3g_dogle_file /usr/sbin/util_sys_cli bgCmd "/usr/sbi" ;; "12d1/1c08/102") echo "E173 Series 3G card out (E173)" >g i=0 while [ "$i" != "5" ] do i=$(($i+1)) sleep 1 if [ ! -e /tmp/read_lock_3g_dogn i=5 fi done rm -f /tmp/3g_in_times rm -f /tmp/3g_umts_mode_switch_done rm -f /tmp/3g_pppd_dial_up_ready rm -f /dev/ttyUSB* rm -f /tmp/3g_dongle_ready_in_times rm -f /tmp/arc_3g_dongle_product_info.tt /usr/sbin/sh_3g_stop.sh rm -f /tmp/read_lock_3g_dogle_file /usr/sbin/util_sys_cli bgCmd "/usr/sbi" ;; *) echo "Not available for the Product ID " ;; esac fi ;; add) [ ${PRODUCT} == "12d1/1446/0" ] && { if [ -e /tmp/3g_in_times ] ; then echo " 12d1/1446/0 second times " > /dev/console else touch /tmp/3g_in_times rm -f /tmp/3g_out_times umts_modeswitch 12d1 1446 > /dev/console fi } # E173 dongle [ ${PRODUCT} == "12d1/1c0b/102" ] && { if [ -e /tmp/3g_in_times ] ; then echo " 12d1/1c0b/102 second times " > /dev/conse else # E173 need modeswitch twice if it's inserted b. switchAgain=0 if [ -e /tmp/3g_out_times ] ; then switchAgain=1 fi touch /tmp/3g_in_times rm -f /tmp/3g_out_times #echo "start to modeswitch for 12d1/1c0b/102" >e umts_modeswitch 12d1 1c0b > /dev/console if [ $switchAgain == "1" ] ; then #echo "AGAIN!!! start to modeswitch fore umts_modeswitch 12d1 1c0b > /dev/console fi fi } # for real 3G dongle, not storage remove.... case "${PRODUCT}" in "12d1/141b/0") if [ -e /tmp/3g_dongle_ready_in_times ] ; then echo " 12d1/141b/0 second times " > /dee else UMTS_PIN_CODE="`/bin/util_ccfg_cli get " touch /tmp/3g_dongle_ready_in_times echo "PIN CODE was ${UMTS_PIN_CODE}" >/e # Be careful, the following task must p. /usr/sbin/sh_3g_wan_pre_init.sh ${PRODU& rm -f /tmp/3g_out_times fi ;; # E173 "12d1/1c08/102") if [ -e /tmp/3g_dongle_ready_in_times ] ; then echo " 12d1/1c08/102 second times " > /e else UMTS_PIN_CODE="`/bin/util_ccfg_cli get " touch /tmp/3g_dongle_ready_in_times echo "PIN CODE was ${UMTS_PIN_CODE}" >/e # Be careful, the following task must p. /usr/sbin/sh_3g_wan_pre_init.sh ${PRODU& rm -f /tmp/3g_out_times fi ;; *) echo "Not available for the Product ID $1" ;; esac ;; esac return 0 Please find a link to a ZIP, containing the WEB UI, copied from the "www" folder. It may be incomplete, I have no idea, but here is what I have: https://rapidshare.com/files/3216522...ghtBox_www.zip [UPDATE] Telnet can be started, if you are connected via the serial port. You just do: Code:
busybox telnetd username: admin password: <your router web UI password> Mobile broadband info popup =================== Last edited by unlokia; 27-January-2012 at 23:05. |
#3
|
|||
|
|||
![]()
TO RE-FLASH PARTITIONS, YOU NEED A TFTP SERVER RUNNING ON A HOST WITH A **STATIC** IP OF: 192.168.1.99, NETMASK OF 255.255.255.0, CONNECTED DIRECTLY TO THE ROUTER *OR* ON A LOCAL NETWORK WITH THE SAME SUBNET (255.255.255.0).
(I use atftpd on Ubuntu, and store my images in /tftpboot) I connect to my Bright Box via serial header & PL2303 USB to serial converter, turn Bright Box ON, then hit any key quickly to get: Code:
BrightBox> You need to download, unZIP and copy the contents of file: https://rapidshare.com/files/1946813...htBox_MTDs.zip ...to your tftp root folder (as mentioned, in Ubuntu using "atftpd", mine is set to /tftpboot). You need to rename them as follows: bootloader manuf nvram pricfg priimg rootfs Rename "bootloader" to "bootldr.bin", and "priimg" to "sysimg.bin" From: Code:
BrightBox> Code:
help Code:
BrightBox>help Available commands: u Update flash image or bootloader m Change the board's manufacture setting c Change the board's setting b Boot program from flash image or from host r Reset the board help Obtain help for CFE commands For more information about a command, enter 'help command-name' *** command status = 0 ### BOOTING ONLY, WITHOUT FLASHING YET ### To boot from "sysimg.bin" stored on your tftp server, type (only TYPE what is in blue!): Code:
BrightBox>b tftp To boot from internal "priimg" partition, type (only TYPE what is in blue!): Code:
BrightBox>b pri ### FLASHING ~~ **POTENTIAL BRICKING AHEAD!!** ### To FLASH your backup of "sysimg.bin", type (only TYPE what is in RED!): !!! THIS WILL FLASH AND OVERWRITE YOUR "priimg" partition - BE WARNED !!! Code:
BrightBox>u pri !!! THIS WILL FLASH AND OVERWRITE YOUR "bootloader" partition - BE WARNED !!! Code:
BrightBox>u boot I have yet to work out how to flash "pricfg" (my settings) back to my Bright Box, to overwrite the stupid ";" semicolon bug I injected, which prevents it from totally booting (the Web UI allows you to backup/restore - why doesn't the terminal?!) Last edited by unlokia; 28-January-2012 at 20:08. |
#4
|
|||
|
|||
![]()
Thoughts? Ideas? Comments?
![]() |
#5
|
||||
|
||||
![]()
v interesting, I like it
![]() |
#6
|
|||
|
|||
![]() |
#7
|
|||
|
|||
![]()
### WORD OF ADVICE ###
DO NOT put Semicolons ";" in the ADSL username... it caused my Bright Box to hang on boot, with this repeated message: Code:
ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ![]() |
#8
|
|||
|
|||
![]()
I have now managed to reset my "Bright Box" back to factory defaults. I must have been holding the reset button down too long. D'oh!
![]() See post #12, for how to reset ### RUNNING AN FTP SERVER FROM THE BOX #### From the serial console, do: Code:
bftpd -d username: admin password: x Last edited by unlokia; 30-January-2012 at 15:16. |
#9
|
|||
|
|||
![]()
Glad you like the router.
|
#10
|
|||
|
|||
![]()
Resetting the Bright Box to factory defaults
=========================== For a normal & fully functioning Bright Box, once it has fully booted (around 5 mins is safe) you can reset it to factory defaults, by holding in the "reset" button (recessed, so a paperclip or pin is needed) for 7 secs will successfully reset it. However, if, like me, you have a brightbox taken apart, connected to a serial port interface (Mine is a PL2303-based USB to serial converter) and monitored via "Hyper Terminal", "PuTTy", "minicom" (Linux) or "gtkterm" (Linux), you can hold down the "reset" button and start the 7 sec count, as soon as you see the word "Hooking" in the serial terminal (show in the code below, in red), which happens ~20 secs from switch on. If you have, like me, tried semicolon ";" injection methods in the web UI, in order to start "telnetd" service (which is what caused mine to hang, and I couldn't work out how to reset it, after trying for a DAY!) then the only way I worked out how to reset it, is from the green paragraph above. Code:
HELO CPUI L1CI DRAM ---- PHYS ZQDN PHYE DINT LSYN USYN MSYN LMBE PASS ---- ZBSS CODE DATA L12F ROMM ==== HELO ZBSS RAMM ==== Copyright (C) 2011 Arcadyan Technology. SPIFLASH: JEDEC ID: 0xc22017, size: 8192KB block: 64KB(64), sector: 4KB(1024) NVRAM(0) MAGIC checking passed! NVRAM(0) CRC checking passed! total 7 of NVRAM(0) entries loaded NVRAM(1) MAGIC checking passed! NVRAM(1) CRC checking passed! total 7 of NVRAM(1) entries loaded BOOTLOADER version 1.0.9 for BrightBox Build Date: Wed Nov 9 10:21:21 2011 (glen_lin@buildbed) Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz Memory Test Passed! Total Memory: 67108864 bytes (64MB) HW Version: 01 Board IP address 192.168.1.1 Board IP netmask 255.255.255.0 Gateway IP address 0.0.0.0 Server IP address 192.168.1.99 Boot image (1 or 2) 1 MAC address number 1 MAC address base 74-31-70-B5-A3-7C *** Press any key to stop auto run (3 seconds) *** Auto run second count down: 0 Loading primary image ... Finished loading 8257536 bytes DATE : Mon Nov 28 17:30:50 2011 VER : v0.09.82.0001 CRC : 3C15DF56 Code Address: 0x80002000, Entry Address: 0x801d8520 Decompression OK! Entry at 0x801d8520 Starting program at 0x801d8520 Linux version 2.6.30 (glen_lin@buildbed) (gcc version 4.1.2) #1 Mon Nov 28 17:16:00 CST 2011 Detected Broadcom 0x6328 CPU revision 10b0 CPU frequency is 320 MHz 64MB of RAM installed registering 32 GPIOs console [early0] enabled CPU revision is: 0002a075 (Broadcom BCM63281) board_bcm9632x: board name: AR7516AAW Determined physical RAM map: memory: 03f00000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00003f00 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00003f00 On node 0 totalpages: 16128 free_area_init_node: node 0, pgdat 8024bb30, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 94 pages used for memmap Normal zone: 11938 pages, LIFO batch:1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16002 Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 ro rootfstype=squashfs wait instruction: enabled Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes NR_IRQS:80 PID hash table entries: 256 (order: 8, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 61368k/64512k available (1912k kernel code, 3124k reserved, 436k data, 120k init, 0k highmem) Calibrating delay loop... 318.46 BogoMIPS (lpj=159232) Mount-cache hash table entries: 512 --Kernel Config-- SMP=0 PREEMPT=0 DEBUG_SPINLOCK=0 DEBUG_MUTEXES=0 net_namespace: 536 bytes /proc/net/netfilter/nf_cli_bw_mon created NET: Registered protocol family 16 registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 pci 0000:00:00.0: PME# supported from D0 D3hot pci 0000:00:00.0: PME# disabled pci 0000:01:00.0: reg 10 64bit mmio: [0x000000-0x003fff] pci 0000:01:00.0: supports D1 D2 pci 0000:00:00.0: PCI bridge, secondary bus 0000:01 pci 0000:00:00.0: IO window: disabled pci 0000:00:00.0: MEM window: 0x10f00000-0x10ffffff pci 0000:00:00.0: PREFETCH window: disabled PCI: Enabling device 0000:00:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:00.0 to 64 BLOG v3.0 Initialized BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 Nov 28 2011 17:14:06 initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered NET: Registered protocol family 1 Total # RxBds=848 bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 119 io scheduler noop registered (default) PCI: Setting latency timer of device 0000:00:00.0 to 64 aer 0000:00:00.0:pcie02: service driver aer loaded bcm632x-uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm632x-uart console handover: boot [early0] -> real [ttyS0] loop: module loaded PPP generic driver version 2.4.2 NET: Registered protocol family 24 PPPoL2TP kernel driver, V1.0 m25p80 spi0.0: mx25l6405d (8192 Kbytes) Creating 6 MTD partitions on "spi0.0": 0x00000000e000-0x00000000f000 : "manuf" 0x00000000f000-0x000000010000 : "nvram" 0x000000110000-0x0000007f0000 : "rootfs" 0x000000010000-0x0000007f0000 : "priimg" 0x0000007f0000-0x000000800000 : "pricfg" 0x000000000000-0x00000000e000 : "bootldr" bcm632x-hsspi bcm632x-hsspi.0: at 0xb0001000 (irq 37, FIFOs size 510) v1.0 Registered led device: dsl:sync Registered led device: dsl:data Registered led device: wps:green Registered led device: sys:a Registered led device: sys:b Registered led device: sys:c Registered led device: sys:d GACT probability on u32 classifier Actions configured TCP cubic registered NET: Registered protocol family 17 Bridge firewalling registered Initializing MCPD Module 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:2. Freeing unused kernel memory: 120k freed gpio-buttons driver version 0.1.2 input: gpio-buttons as /devices/platform/gpio-buttons/input/input0 Button Hotplug driver version 0.4.1 arc_oshal: module license 'Propritary' taints kernel. Disabling lock debugging due to kernel taint oshal_init(1066) DRV: Created Successfully ARC_KERNEL_OSIX_init(396) DRV: Created Successfully Broadcom Logger v0.1 Nov 28 2011 17:16:27 Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Nov 28 2011 17:16:29 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Nov 28 2011 17:16:29 Broadcom BCM6328B0 Ethernet Network Device v0.1 Nov 28 2011 17:16:31 ETH Init: Ch:0 - 180 tx BDs at 0xa3946000 ETH Init: Ch:0 - 400 rx BDs at 0xa3a21000 bcm632x-dg: register bcmsw eth0: MAC Address: 74:31:70:B5:A3:7C eth1: MAC Address: 74:31:70:B5:A3:7C eth2: MAC Address: 74:31:70:B5:A3:7C eth3: MAC Address: 74:31:70:B5:A3:7C Broadcom 802.1Q VLAN Interface, v0.1 bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.4 Nov 28 2011 17:16:44 bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom Power Management v0.1 Nov 28 2011 17:18:42 Broadcom WLAN configuration service start PCI: Enabling device 0000:01:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:01:00.0 to 64 wl: passivemode=1 wl: napimode=0 wl: allocskbmode=1 wl:force using embedded data wlc_bmac_attach(2582): BpGetWirelessFlags NIY! wl0: Broadcom BCMa8dc 802.11 Wireless Controller 5.100.96.0.cpe4.10L01a.8 bcm632x-dg: register wl0 ip_tables: (C) 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (1008 buckets, 4032 max) ctnetlink v0.93: registering with nfnetlink. xt_time: kernel timezone is -0000 IMQ driver loaded successfully. Hooking IMQ after NAT on PREROUTING. Hooking IMQ before NAT on POSTROUTING. Osix_service_sys_cmd_thread_main[1302]: Osix Wait for Batch System Comand Processing... Osix Thread service system command started successfully ! ramdisk/etc/config/ ramdisk/etc/config/backup.bin ramdisk/etc/config/glbcfg.save MHDL_DB_WLAN_Init_Setting[118] MHDL_DB_LAN_Init_Setting[525] Password for 'admin' changed BcmAdsl_Initialize=0xC040AEF8, g_pFnNotifyCallback=0xC04C08D4 BcmAdsl_Initialize(202): BpGetRj11InnerOuterPairGpios NIY pSdramPHY=0xA3FFFFF8, 0xD11BD1AB 0xD99AD3DB *** PhySdramSize got adjusted: 0x82CDC => 0x98878 *** AdslCoreSharedMemInit: shareMemAvailable=423776 AdslCoreHwReset: pLocSbSta=83120000 bkupThreshold=1600 AdslCoreHwReset: AdslOemDataAddr = 0xA3F77D28 EXECUTE "/bin/util_xdsl_cli mode auto" BcmAdsl_Initialize=0xC040AEF8, g_pFnNotifyCallback=0xC04C08D4 EXECUTE "/bin/util_xdsl_cli bitswap enable" BcmAdsl_Initialize=0xC040AEF8, g_pFnNotifyCallback=0xC04C08D4 EXECUTE "/bin/util_xdsl_cli sra enable" BcmAdsl_Initialize=0xC040AEF8, g_pFnNotifyCallback=0xC04C08D4 devCtl_xtmInitiaXTM Init: Ch:0 - 400 rx BDs at 0xa3bc5000 lize(174): devCtXTM Init: Ch:1 - 16 rx BDs at 0xa29ad780 l_getSdramSize NIY! WAN Type is ADSL Success Success Success Success Success Success Power ON stage, no need to delete interface in advance. ioctl failed. check if wl0.1 exists MHDL_DB_SYS_DNS_UPDATE_RESOLV_CONF[1046]: cmd_buf (cp /tmp/tmpResolv_536.conf /etc/resolv.conf) dhcp IP compare: old () vs new (192.168.1.101). dhcp lease time compare: old (00000000) vs new (0002A300). mhdl_dn_lan_dhcpd_cfg_file_init[169]: Check_IP_Changed : (TRUE). Lease_Time_Changed (TRUE) dhcp IP compare: old () vs new (192.168.2.1). dhcp lease time compare: old (00000000) vs new (0000A8C0). mhdl_dn_lan_dhcpd_cfg_file_init[169]: Check_IP_Changed : (TRUE). Lease_Time_Changed (TRUE) dhcp IP compare: old () vs new (192.168.3.1). Restart Level is BR0_IPCHANGED BR0 IP Changed dhcp lease time compare: old (00000000) vs new (0000A8C0). mhdl_dn_lan_dhcpd_cfg_file_init[169]: Check_IP_Changed : (TRUE). Lease_Time_Changed (TRUE) Initializing WAN ioctl failed. check if wl0.1 exists XTM driver returns Not Found Error bcmxtmrt: MAC address: 74 31 70 b5 a3 7e [DoCreateDeviceReq.2998]: register_netdev [DoCreateDeviceReq.3000]: register_netdev done /bin/bcm_atmctl operate conn --add 1.0.38 aal5 vcmux_pppoa 1MHDL_DB_SYS_STOP_UPNPD[1322]: cmd (killall arc_upnp) killall: arc_upnp: no process killed MHDL_DB_SYS_RESTART_UPNPD[1306]: cmd_buf: /usr/sbin/arc_upnp & Success EXECUTE "/bin/pppd -c pppoa1 -a atm0.0.0.38 -H -k -R 30 -K 60 -M 1492 -u readytoconnect@fs -p mistyview &" Success Success Success Success ioctl failed. check if wl0.1 exists PPP: pppoa1 Start to connect ... netdev path : pppoa1 -> atm0 modprobe: can't open 'modules.dep': No such file or directory The kernel doesn't support the ebtables 'nat' table. ioctl failed. check if wl0.1 exists iptables v1.4.8: Couldn't find target `QOSUP' Try `iptables -h' or 'iptables --help' for more information. iptables v1.4.8: Couldn't find target `QOSUP' Try `iptables -h' or 'iptables --help' for more information. net.netfilter.nf_conntrack_acct = 1 ioctl failed. check if wl0.1 exists RTNETLINK answers: Invalid argument CLOCK_MONOTONIC, resolution=0.999848 System clock_res=999848, clock_hz=1000 config_httpd(517) LAN IP Address (192.168.1.101) Pre-init before any Application was started. config_httpd(526) LAN IP Mask (255.255.255.0) httpd: after config_httpd() httpd: listen at 192.168.1.101:5438 [HTTPD] httpd_main(): Not the 1st httpd_main task killall: dyndns: no process killed killall: tzoupdate: no process killed start httpd Success Success Success SSDP_SetRCVSocket(217): Recv SsdpSock 14 Success Success QueryEthernetLinkStatus[115]: WAN Interface Name (NULL) Port Number: eth3, PortStatus: 0 killall: bcm_mcpd: no process killed ioctl failed. check if wl0.1 exists killall arc_httpd start arc_httpd lease_init[65]: /etc/udhcpd/udhcpd_001.leases ! 1 Jan 00:00:27 sntp[982]: kod_init_kod_db(): Cannot open KoD db file /var/db/ntp-kod 1 Jan 00:00:27 sntp[982]: Error looking up (A) ntp.readytoconnect.co.uk: Name or service not known Unable to resolve hostname(s) HTTPD: main(1478) Restart Level is BR1_IPCHANGED BR1 IP Changed main(1570): I am child for HTTPD SVR 2 main(1582): Start HTTPD SVR 0 ioctl failed. check if wl0.1 exists killall: bcm_mcpd: no process killed lease_init[65]: /etc/udhcpd/udhcpd_002.leases ! Restart Level is BR2_IPCHANGED BR2 IP Changed please assign value for wl0.1_ssid please assign value for wl0.2_ssid killall: bcm_mcpd: no process killed iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. ioctl failed. check if wl0.1 exists iptables: No chain/target/match by that name. conntrack v1.0.0 (conntrack-tools): connection tracking table has been emptied. conntrack v1.0.0 (conntrack-tools): expectation table has been emptied. ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists rmmod: can't unload 'nf_nat_pt': unknown symbol in module, or unknown parameter ioctl failed. check if wl0.1 exists killall: urlfilterd: no process killed ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists ioctl failed. check if wl0.1 exists conntrack v1.0.0 (conntrack-tools): connection tracking table has been emptied. conntrack v1.0.0 (conntrack-tools): expectation table has been emptied. ioctl failed. check if wl0.1 exists please assign value for wl0_radius_key please assign value for wl0_nas_id 1 Jan 00:00:50 sntp[2769]: Error looking up (A) ntp.readytoconnect.co.uk: Name or service not known Unable to resolve hostname(s) ioctl failed. check if wl0.1 exists please assign value for wl0.1_wpa_psk please assign value for wl0.2_wpa_psk start WLAN manager WLmngr Daemon is running ioctl failed. check if wl0.1 exists ifconfig: wl0.1: error fetching interface information: Device not found ifconfig: wl0.2: error fetching interface information: Device not found wlevt_init@157: opened loopback socket 6 wlevt is ready for new msg... nvram_commit NIY! ifconfig: wl0.1: error fetching interface information: Device not found ifconfig: wl0.2: error fetching interface information: Device not found ioctl failed. check if wl0.1 exists >>>>>Start Auto Channel search !!! >>>>> Setting SSID: "BrightBox-rc3bq3" Setting SSID: "ar7516aaw-guest" Setting SSID: "ar7516aaw-guest2" PPP: pppoa1 Start to connect ... netdev path : pppoa1 -> atm0 chanspec 0x2b01 selected bcm_wlctl: Unsupported bcm_wlctl: Not Permitted bcm_wlctl: Undefined error nvram_commit NIY! LLTD daemon is ready to run EAP daemon is ready to run NAS daemon is ready to run wlmngr_startWsc(1125): wait for WPSUI message timeout! dalQos_setDefaultWlQueuesLock NIY! dalQos_setDefaultWlQueuesLock NIY! dalQos_setDefaultWlQueuesLock NIY! read/write to TR69 configuration NIY! Starting to init bandwidth contrl of wifi!! /sbin/tctrl qdisc del dev wl0 ingress 2>/dev/null /usr/sbin/ebtables -X wl0_egress 2>/dev/null iptables: No chain/target/match by that name. /sbin/tctrl qdisc del dev wl0 root 2>/dev/null /usr/sbin/ebtables -X wl0_ingress 2>/dev/null /sbin/tctrl qdisc del dev wl0.1 ingress 2>/dev/null /usr/sbin/ebtables -X wl0.1_egress 2>/dev/null /sbin/tctrl qdisc del dev wl0.1 root 2>/dev/null /usr/sbin/ebtables -X wl0.1_ingress 2>/dev/null /sbin/tctrl qdisc del dev wl0.2 ingress 2>/dev/null /usr/sbin/ebtables -X wl0.2_egress 2>/dev/null /sbin/tctrl qdisc del dev wl0.2 root 2>/dev/null /usr/sbin/ebtables -X wl0.2_ingress 2>/dev/null start mcpd 1 Jan 00:01:15 sntp[3572]: Error looking up (A) ntp.readytoconnect.co.uk: Name or service not known Unable to resolve hostname(s) start USB service Password for 'user' changed Password for 'matt' changed bcm632x-usb-ohci bcm632x-usb-ohci.0: init err (c8300000 0000) bcm632x-usb-ohci bcm632x-usb-ohci.0: startup error -79 bcm632x-usb-ohci: probe of bcm632x-usb-ohci.0 failed with error -79 action name is add product name is 1d6b/2/206 Driver 'sd' needs updating - please use bus_type methods start UMTS service action name is add product name is 1d6b/2/206 start Power-Management service Host MIPS Clock divider pwrsaving is enabled DDR Self Refresh pwrsaving is enabled System Start with Normal Phase root@BrightBox:/ # RED = time to hold down reset for 7 secs, when you see "HOOKING..." in red (~20 secs from power switch ON, counting "0" when you first hold in the reset switch, and "7" when you let go; 7 REAL seconds, counting from 0-7 [not many people do that - they count "one..." the instant they hold it down, which is wrong"]) #### BACKUP YOUR BRIGHT BOX PARTITIONS #### 1/ Download the attached ZIP file, extract the shell script, and copy it to a USB drive (FAT/FAT32). 2/ Plug the USB drive into the Bright Box, and wait about 1 min for it to mount 3/ Using serial console/telnet (see above for how to start telnet) navigate to /mnt/<name of your USB drive here> (mine is "usb1_1") 4/ Run the shell script (it's in the USB drive, right? VITAL!), to make backups of your partitions: Code:
./backup_brightbox_partitions.sh ![]() Source of script: Code:
#!/bin/sh echo "### backing up your partitions to USB drive ####" echo "##################################################" echo "### in five seconds... ###" sleep 5 echo "##################################################" echo "processing..." cat /dev/mtd0 > manuf echo "### mtd0 done ###" cat /dev/mtd1 > nvram echo "### mtd1 done ###" cat /dev/mtd2 > rootfs echo "### mtd2 done ###" cat /dev/mtd3 > priimg echo "### mtd3 done ###" cat /dev/mtd4 > pricfg echo "### mtd4 done ###" cat /dev/mtd5 > bootldr echo "### mtd5 done ###" sleep 2 echo "All done. Backups are saved in the USB drive you plugged into Bright Box" Last edited by unlokia; 30-January-2012 at 15:20. |
#11
|
|||
|
|||
![]()
I'm still astounded that 661 people have viewed this thread, and yet only ONE person has replied!
![]() Last edited by unlokia; 31-January-2012 at 06:35. |
#12
|
|||
|
|||
![]()
Someone reply...
![]() Last edited by unlokia; 01-February-2012 at 01:48. |
#13
|
|||
|
|||
![]()
How does it perform as a router?
|
#14
|
|||
|
|||
![]()
I've no idea yet. I'll have to try it and see!
![]() |
#15
|
|||
|
|||
![]()
Okay. I downloaded another version of "busybox" called "busybox-mips" as a temporary hack, so that I have more commands I can run on Bright Box.
### HOW TO SERVE A WEB PAGE ### 1/ Download: https://rapidshare.com/files/3545138...ght_box_v1.zip 2/ UnZIP the file, and place the three files inside, into the root of a USB drive, and plug it into Bright Box USB port. 3/ From serial console/telnet, cd to /mnt/<your USB device root> and execute the "start_www.sh" script (you type what is in blue): Code:
root@BrightBox:/mnt/usb1_1 # ./start_www.sh Code:
#!/bin/sh # simple Bright Box server start script - VERY rough. # kill the built-in http server off killall arc_httpd #make a ramdisk folder for faster running mkdir /ramdisk/www #copy an imageof Bright Box :-) cp ./bbox.jpg /ramdisk/www #create a temporary, basic html page echo "<html><body bgcolor="#FF6600"><h1>This is a test by unlokia</h1><br><h2>busybox-mips</h2><img src="bbox.jpg"></body></html>" > /ramdisk/www/index.html #start our http server ;-) ./busybox-mips httpd -h /ramdisk/www [UPDATE] I just ran "strings" on "arc_httpd" binary, and got: Code:
/lib/ld-uClibc.so.0 _init _fini __uClibc_main _Jv_RegisterClasses libarc_osix.so _DYNAMIC_LINKING __RLD_MAP _GLOBAL_OFFSET_TABLE_ __dso_handle libmapi_mid_core.so libmapi_sys.so libmapi_sw.so libmapi_ccfg.so libmapi_xdsl.so libmapi_wlan.so libmapi_nat.so libmapi_lan.so libmapi_atm.so libmapi_3g.so libmapi_wan.so libmapi_vlan.so libmapi_fw.so libmapi_iptables.so libmapi_nas.so libpthread.so.0 libbcm_ethswctl.so libarc_hal.so libmhdl_sys.so libmhdl_sw.so libmhdl_ccfg.so libmhdl_xdsl.so libmhdl_wlan.so libmhdl_nat.so libmhdl_lan.so libmhdl_atm.so libmhdl_3g.so libmhdl_wan.so libmhdl_vlan.so libmhdl_fw.so libmhdl_nas.so libmhdl_iptables.so libmhdl_mid_core.so libmhdl_clientmon.so strlen strncpy sscanf hsearch_r hdestroy_r strsep hcreate_r strpbrk set_cgi strchr unlink stdout fprintf exit strcpy fcntl fgets fputs memset sprintf fflush fopen fclose snprintf inet_ntoa atoi accept __errno_location perror strcmp strtoul strstr strncmp chdir signal socket setsockopt bind listen stderr getpid fork userinfo strcspn str2arglist init_check_list fileno fgetc __fgetc_unlocked Slurp_buf_buf gmtime strftime no_cache send_not_found send_ok fputc __fputc_unlocked sysinfo CFG_get inet_addr init_user_config user_logout user_islogin fdopen strncasecmp strspn strcasecmp HTTP_INDEX mime_handlers HTTP_HIDDEN_PAGES HTTP_HIDDEN_PAGE_NUM match_urn bypass_check HTTP_LOGIN HTTP_LOGIN_ERR HTTP_LOGIN_DUP send_redirect shutdown HTTP_SERVER_PORT HTTP_NEEDNT_AUTH init_bypass_list daemon childProcessHandler MD5Update MD5Init MD5Final __ctype_b script_handlers Osix_osSystem system mapi_fw_cmdctl sleep strcat user_list _CB_CGI_CFG_ARY admin_ip user_escape CFG_str2id CFG_list str_escape CFG_get_str script_Args cgi_show_result post_buf init_cgi get_cgi user_name user_login HTTP_LOGIN_OK ps_cgi_cmds str_unescape CFG_set_str as_cgi_cmds ftok msgget msgsnd Tr69Rpcmethod_SendMsg clearerr ferror select cgi_safe_fread cgi_waitfor feof cgi_safe_fwrite CFG_id2str do_script do_auth do_file attach CGI_do_DSL_CONF_ps CGI_do_DSL_RETRAIN_ps CGI_do_DNS_CONF_ps CGI_do_DDNS_CONF_ps CGI_do_LAN_CONF_ps CGI_do_LAN_DHCP_REV_CONF_ps CGI_do_LAN_DHCP_REV_DEL_CONF_ps CGI_do_SYS_CONF_ps CGI_do_SYS_RESET_ps CGI_do_SYS_MFRESET_ps CGI_do_SYS_BOOT_ps CGI_do_SYS_RMT_MGMT_ps CGI_do_WIFI_CONF_ps CGI_do_WIFI_WEP_CONF_ps CGI_do_WIFI_SSID_CONF_ps CGI_do_WIFI_SSID_SEC_ps CGI_do_WIFI_SSID_QOS_CONF_ps CGI_do_WIFI_ADV_CONF_ps CGI_do_WIFI_MAC_CONF_ps CGI_do_WIFI_WPA_CONF_ps CGI_do_WIFI_WPS_CONF_ps CGI_do_WIFI_WPS_ENROLL_CONF_ps CGI_do_WIFI_WPS_STARTPBC_CONF_ps CGI_do_WIFI_DOT1X_CONF_ps CGI_do_WAN_ATM_CONF_ps CGI_do_WAN_ADSL_ETH_CONF_ps CGI_do_WAN_CONN_ps CGI_do_WAN_DISC_ps CGI_do_NAT_CONF_ps CGI_do_NAT_ADDRMAP_ps CGI_do_NAT_VIRTUALSERVER_ps CGI_do_NAT_APP_ps CGI_do_NTP_CONF_ps CGI_do_WANETH_CONN_ps CGI_do_WANETH_DISC_ps CGI_do_LOG_CLR_ps CGI_do_TR69_CONF_ps CGI_do_FW_CONF_ps CGI_do_FW_FILTER_CONF_ps CGI_do_FW_FILTER_DEL_ps CGI_do_FW_SCHEDULE_CONF_ps CGI_do_FW_SCHEDULE_DEL_ps CGI_do_FW_URL_LIST_CONF_ps CGI_do_FW_URL_LIST_CLEAR_ps CGI_do_FW_MAC_CONF_ps CGI_do_FW_DMZ_CONF_ps CGI_do_FW_SPI_CONF_ps CGI_do_UPNP_CONF_ps CGI_do_QOS_CONF_ps CGI_do_QOS_RULE_CONF_ps CGI_do_QOS_RULE_EDIT_CONF_ps CGI_do_NAS_USER_CONF_ps CGI_do_UMTS_PINCODE_CONF_ps CGI_do_NAS_CONF_ps CGI_do_NAS_BASIC_CONF_ps CGI_do_DSL_CONF_as CGI_do_DSL_RETRAIN_as CGI_do_DNS_CONF_as CGI_do_DDNS_CONF_as CGI_do_LAN_CONF_as CGI_do_LAN_DHCP_REV_CONF_as CGI_do_LAN_DHCP_REV_DEL_CONF_as CGI_do_SYS_CONF_as CGI_do_SYS_RESET_as CGI_do_SYS_MFRESET_as CGI_do_SYS_BOOT_as CGI_do_SYS_RMT_MGMT_as CGI_do_WIFI_CONF_as CGI_do_WIFI_WEP_CONF_as CGI_do_WIFI_SSID_CONF_as CGI_do_WIFI_SSID_SEC_as CGI_do_WIFI_SSID_QOS_CONF_as CGI_do_WIFI_ADV_CONF_as CGI_do_WIFI_MAC_CONF_as CGI_do_WIFI_WPA_CONF_as CGI_do_WIFI_WPS_CONF_as CGI_do_WIFI_WPS_ENROLL_CONF_as CGI_do_WIFI_WPS_STARTPBC_CONF_as CGI_do_WIFI_DOT1X_CONF_as CGI_do_WAN_ATM_CONF_as CGI_do_WAN_ADSL_ETH_CONF_as CGI_do_WAN_CONN_as CGI_do_WAN_DISC_as CGI_do_NAT_CONF_as CGI_do_NAT_ADDRMAP_as CGI_do_NAT_VIRTUALSERVER_as CGI_do_NAT_APP_as CGI_do_NTP_CONF_as CGI_do_WANETH_CONN_as CGI_do_WANETH_DISC_as CGI_do_LOG_CLR_as CGI_do_TR69_CONF_as CGI_do_FW_CONF_as CGI_do_FW_FILTER_CONF_as CGI_do_FW_FILTER_DEL_as CGI_do_FW_SCHEDULE_CONF_as CGI_do_FW_SCHEDULE_DEL_as CGI_do_FW_URL_LIST_CONF_as CGI_do_FW_URL_LIST_CLEAR_as CGI_do_FW_MAC_CONF_as CGI_do_FW_DMZ_CONF_as CGI_do_FW_SPI_CONF_as CGI_do_UPNP_CONF_as CGI_do_QOS_CONF_as CGI_do_QOS_RULE_CONF_as CGI_do_QOS_RULE_EDIT_CONF_as CGI_do_NAS_USER_CONF_as CGI_do_NAS_USER_DEL_CONF_as CGI_do_USB_MOUNT_DEL_CONF_as CGI_do_USB_SHARED_CONF_as CGI_do_USB_SHARED_DEL_CONF_as CGI_do_UMTS_PINCODE_CONF_as CGI_do_NAS_CONF_as CGI_do_NAS_BASIC_CONF_as ioctl waitpid setsid dup2 setenv alarm execvp _cfg_get _cfg_set LAN_IP4ADDR_set LAN_DHCP_LOG_100_LST_get LAN_DHCP_CLIENT_NUM_get LAN_PORT_STATUS_004_LST_get LAN_DHCP_REV_024_LST_get WANETH_PROTO_set WANETH_VLAN_get WANETH_VLAN_set WANETH_PASSWORD_get WANETH_PASSWORD_set WANETH_STATIC_DNS_set WANETH_PRI_DNS_set WANETH_SEC_DNS_set WANETH_TYPE_get WANETH_STATUS_get WANETH_STATUS_MAC_get WANETH_STATUS_IP_get WANETH_STATUS_MASK_get WANETH_STATUS_GW_get WANETH_STATUS_DNS_PRI_get WANETH_STATUS_DNS_SEC_get WANETH_STATUS_RATE_get WAN_PROTO_set WAN_VLAN_get WAN_VLAN_set WAN_PASSWORD_get WAN_PASSWORD_set WAN_STATIC_DNS_set WAN_PRI_DNS_set WAN_SEC_DNS_set WAN_PVC_STATUS_008_LST_get WAN_PPP_STATUS_get WAN_PPP_CON_TIME_get WAN_STATUS_IP_get SYSTEM_LANG_CODE_get SYSTEM_LANG_CODE_set SYSTEM_TIME_ZONE_get SYSTEM_TIME_ZONE_set SYSTEM_GUI_STYLE_get SYSTEM_GUI_STYLE_set SYSTEM_HOST_NAME_get SYSTEM_HOST_NAME_set SYSTEM_WAN_TYPE_get SYSTEM_WAN_TYPE_set SYSTEM_ACTIVE_WAN_TYPE_get SYSTEM_ACTIVE_WAN_TYPE_set SYSTEM_PPP_PASS_THRU_get SYSTEM_PPP_PASS_THRU_set SYSTEM_CURRENT_TIME_get SYSTEM_RUNTIME_CODE_VER_get SYSTEM_BOOT_CODE_VER_get SYSTEM_SERIAL_NUM_get SYSTEM_LAN_MAC_002_LST_get SYSTEM_WAN_MAC_008_LST_get SYSTEM_WLAN_MAC_002_LST_get SYSTEM_HARDWARE_VER_get SYSTEM_SECURITY_LOG_100_LST_get WIRELESS_WPS_PCB_get WIRELESS_WPS_PCB_set WIRELESS_CHAN_LST_get WIRELESS_WPS_STATUS_get WIRELESS_CHANBOND_LST_get WIRELESS_PWS_TYPE_get WIRELESS_PWS_ENCRTYPE_get WIRELESS_AP_PIN_get WIRELESS_SEC_KEY_get WIFISSID_WLAN_STATUS_002_LST_get WIFIMACFILTER_FILTER_ENABLE_get WIFIMACFILTER_FILTER_ENABLE_set WIFIMACFILTER_FILTER_ACCESS_get WIFIMACFILTER_FILTER_ACCESS_set WIFIMACFILTERADDR_MACFILTER_ADDR_get WIFIMACFILTERADDR_MACFILTER_ADDR_set DOT1X_CYPHER_SUITE_get DOT1X_CYPHER_SUITE_set DOT1X_DOT1XREKEYSECONDS_get DOT1X_DOT1XREKEYSECONDS_set DOT1X_DOT1XREKEYPACKETS_get DOT1X_DOT1XREKEYPACKETS_set DOT1X_SSNREKEYSECONDS_get DOT1X_SSNREKEYSECONDS_set DOT1X_SSNREKEYPACKETS_get DOT1X_SSNREKEYPACKETS_set DOT1X_DOT1XREKEYING_get DOT1X_DOT1XREKEYING_set DOT1X_SSNREKEYING_get DOT1X_SSNREKEYING_set DOT1X_STRICTUPDATE_get DOT1X_STRICTUPDATE_set DOT1X_ENABLEOS_get DOT1X_ENABLEOS_set DOT1X_ENABLEWEP_get DOT1X_ENABLEWEP_set DOT1X_ENABLEACL_get DOT1X_ENABLEACL_set DOT1X_ENABLESSN_get DOT1X_ENABLESSN_set DOT1X_WPA2FLAG_get DOT1X_WPA2FLAG_set DOT1X_ENABLESSNPSK_get DOT1X_ENABLESSNPSK_set DOT1X_SSNPSK256KEYFILED_get DOT1X_SSNPSK256KEYFILED_set DOT1X_WEPKEYSIZE_get DOT1X_WEPKEYSIZE_set DOT1X_DEFAULTKEYID_get DOT1X_DEFAULTKEYID_set DOT1X_SSNPSKASCIIKEY_get DOT1X_SSNPSKASCIIKEY_set DOT1X_SSNPSK256KEY_get DOT1X_SSNPSK256KEY_set DOT1X_SRV_TYPE_get DOT1X_SRV_TYPE_set DOT1X_ACC_SRV_PORT_get DOT1X_ACC_SRV_PORT_set DOT1X_TXPERIOD_get DOT1X_TXPERIOD_set DOT1X_SUPPTIMEOUT_get DOT1X_SUPPTIMEOUT_set DOT1X_REAUTHCOUNT_get DOT1X_REAUTHCOUNT_set DOT1X_ENABLE1XAUTHEN_get DOT1X_ENABLE1XAUTHEN_set DOT1X_ROLE_get DOT1X_ROLE_set HTTPD_WAIT_TIMEOUT_get HTTPD_WAIT_TIMEOUT_set HTTPD_REMOTE_MGNT_get HTTPD_REMOTE_MGNT_set HTTPD_HTTP_BROWSE_SERVICE_get HTTPD_HTTP_BROWSE_SERVICE_set HTTPD_HTTP_BROWSE_PORT_get HTTPD_HTTP_BROWSE_PORT_set PVC_PVC_LST_get USB_MAXSUPPORTNUM_get USB_MAXSUPPORTNUM_set USB_ENABLE_get USB_ENABLE_set USB_MAXNUM_get USB_MAXNUM_set DRIVE_NOW_DRIVE_NUM_get DRIVE_NOW_DRIVE_NUM_set DRIVE_NOW_DRIVEINFOA_get DRIVE_NOW_DRIVEINFOA_set DRIVE_NOW_VOLUMEA_get DRIVE_NOW_VOLUMEA_set DRIVE_NOW_DRIVEINFOB_get DRIVE_NOW_DRIVEINFOB_set DRIVE_NOW_VOLUMEB_get DRIVE_NOW_VOLUMEB_set PRINTER_NOW_NUM_get PRINTER_NOW_NUM_set PRINTER_NOW_MODEL_get PRINTER_NOW_MODEL_set UMTS_NOW_NUM_get UMTS_NOW_NUM_set UMTS_NOW_MANUFACTURER_get UMTS_NOW_MANUFACTURER_set UMTS_NOW_MODEL_get UMTS_NOW_MODEL_set SAMBA_HISTORY_DRIVE1_get SAMBA_HISTORY_DRIVE1_set SAMBA_HISTORY_DRIVE2_get SAMBA_HISTORY_DRIVE2_set SAMBA_HISTORY_DRIVE3_get SAMBA_HISTORY_DRIVE3_set SAMBA_HISTORY_DRIVE4_get SAMBA_HISTORY_DRIVE4_set SAMBA_HISTORY_DRIVE5_get SAMBA_HISTORY_DRIVE5_set SAMBA_HISTORY_DRIVE6_get SAMBA_HISTORY_DRIVE6_set SAMBA_HISTORY_DRIVE7_get SAMBA_HISTORY_DRIVE7_set SAMBA_HISTORY_DRIVE8_get SAMBA_HISTORY_DRIVE8_set SAMBA_HISTORY_HISTORY_get SAMBA_HISTORY_HISTORY_set SAMBA_SHARELIST_DRIVE1_get SAMBA_SHARELIST_DRIVE1_set SAMBA_SHARELIST_DRIVE2_get SAMBA_SHARELIST_DRIVE2_set SAMBA_ENABLE_get SAMBA_ENABLE_set SAMBA_PRESMBENB_get SAMBA_PRESMBENB_set SAMBA_DEF_SMBENABLE_get SAMBA_DEF_SMBENABLE_set SAMBA_DEF_COMPUTERNAME_get SAMBA_DEF_COMPUTERNAME_set SAMBA_DEF_COMPUTERDESCRIPTION_get SAMBA_DEF_COMPUTERDESCRIPTION_set SAMBA_DEF_GROUPNAME_get SAMBA_DEF_GROUPNAME_set SAMBA_DEF_REMOTEENABLE_get SAMBA_DEF_REMOTEENABLE_set SAMBA_SMBENABLE_get SAMBA_SMBENABLE_set SAMBA_COMPUTERNAME_get SAMBA_COMPUTERNAME_set SAMBA_COMPUTERDESCRIPTION_get SAMBA_COMPUTERDESCRIPTION_set SAMBA_GROUPNAME_get SAMBA_GROUPNAME_set SAMBA_REMOTEENABLE_get SAMBA_REMOTEENABLE_set PRINTER_ENABLE_get PRINTER_ENABLE_set PRINTER_QUEUENAME_get PRINTER_QUEUENAME_set UPNP_ENABLE_get UPNP_ENABLE_set LOG_CATEGORY_get LOG_CATEGORY_set QOS_DFT_TOTAL_FWG_NUM_get QOS_DFT_TOTAL_FWG_NUM_set QOS_DFT_DFT_FWG_get QOS_DFT_DFT_FWG_set QOS_DFT_LNK_NUM_get QOS_DFT_LNK_NUM_set QOS_DFT_LNK0_get QOS_DFT_LNK0_set QOS_DFT_VIF0_0_get QOS_DFT_VIF0_0_set QOS_DFT_FWG00_0_get QOS_DFT_FWG00_0_set QOS_DFT_FWG00_1_get QOS_DFT_FWG00_1_set QOS_DFT_FWG00_2_get QOS_DFT_FWG00_2_set QOS_DFT_FWG00_3_get QOS_DFT_FWG00_3_set QOS_DFT_FWG00_4_get QOS_DFT_FWG00_4_set QOS_DFT_FWG00_5_get QOS_DFT_FWG00_5_set QOS_DFT_FWG00_6_get QOS_DFT_FWG00_6_set QOS_DFT_FWG00_7_get QOS_DFT_FWG00_7_set QOS_DFT_CLSFY_SEQ_get QOS_DFT_CLSFY_SEQ_set QOS_DFT_RU00_MAC_get QOS_DFT_RU00_MAC_set QOS_DFT_RU00_INIF_get QOS_DFT_RU00_INIF_set QOS_DFT_RU00_INPHYIF_get QOS_DFT_RU00_INPHYIF_set QOS_DFT_RU00_SRCIP_get QOS_DFT_RU00_SRCIP_set QOS_DFT_RU00_DSTIP_get QOS_DFT_RU00_DSTIP_set QOS_DFT_RU00_APORPROTO_get QOS_DFT_RU00_APORPROTO_set QOS_DFT_RU00_SPORT_get QOS_DFT_RU00_SPORT_set QOS_DFT_RU00_DPORT_get QOS_DFT_RU00_DPORT_set QOS_DFT_RU00_TOS_get QOS_DFT_RU00_TOS_set QOS_DFT_RU00_8021P_get QOS_DFT_RU00_8021P_set QOS_DFT_RU00_ETHTYPE_get QOS_DFT_RU00_ETHTYPE_set QOS_DFT_RU00_PKTLEN_get QOS_DFT_RU00_PKTLEN_set QOS_DFT_RU00_ACT_get QOS_DFT_RU00_ACT_set QOS_DFT_RU01_MAC_get QOS_DFT_RU01_MAC_set QOS_DFT_RU01_INIF_get QOS_DFT_RU01_INIF_set QOS_DFT_RU01_INPHYIF_get QOS_DFT_RU01_INPHYIF_set QOS_DFT_RU01_SRCIP_get QOS_DFT_RU01_SRCIP_set QOS_DFT_RU01_DSTIP_get QOS_DFT_RU01_DSTIP_set QOS_DFT_RU01_APORPROTO_get QOS_DFT_RU01_APORPROTO_set QOS_DFT_RU01_SPORT_get QOS_DFT_RU01_SPORT_set QOS_DFT_RU01_DPORT_get QOS_DFT_RU01_DPORT_set QOS_DFT_RU01_TOS_get QOS_DFT_RU01_TOS_set QOS_DFT_RU01_8021P_get QOS_DFT_RU01_8021P_set QOS_DFT_RU01_ETHTYPE_get QOS_DFT_RU01_ETHTYPE_set QOS_DFT_RU01_PKTLEN_get QOS_DFT_RU01_PKTLEN_set QOS_DFT_RU01_ACT_get QOS_DFT_RU01_ACT_set PWRSAVE_ENABLE_get PWRSAVE_ENABLE_set PWRSAVE_MAX_PERIOD_get PWRSAVE_MAX_PERIOD_set PWRSAVE_PERIOD1_B_get PWRSAVE_PERIOD1_B_set PWRSAVE_PERIOD1_E_get PWRSAVE_PERIOD1_E_set PWRSAVE_PERIOD2_B_get PWRSAVE_PERIOD2_B_set PWRSAVE_PERIOD2_E_get PWRSAVE_PERIOD2_E_set PWRSAVE_PERIOD3_B_get PWRSAVE_PERIOD3_B_set PWRSAVE_PERIOD3_E_get PWRSAVE_PERIOD3_E_set FWACCESSCONTROL_BLOCK_SERVICE_get FWACCESSCONTROL_BLOCK_SERVICE_set FWACCESSCONTROL_USER_PROTOCOL_get FWACCESSCONTROL_USER_PROTOCOL_set FWACCESSCONTROL_USER_PORT_get FWACCESSCONTROL_USER_PORT_set FWACCESSCONTROL_AVAIL_IDX_get FWSCHEDULE_AVAIL_IDX_get FWMACFILTER_DHCP_CLIENT_LIST_get NAT_MAPPING_254_LST_get DLNAS_UPNP_AV_get DLNAS_UPNP_AV_set DLNAS_UPNP_DEFAULT_AV_get DLNAS_UPNP_DEFAULT_AV_set DLNAS_MUSIC_NUM_get DLNAS_MUSIC_NUM_set DLNAS_VIDEO_NUM_get DLNAS_VIDEO_NUM_set DLNAS_PICTURE_NUM_get DLNAS_PICTURE_NUM_set DLNAS_DLNA_SCANNING_get DLNAS_DLNA_SCANNING_set DLNAS_WEB_UPNP_AV_get DLNAS_WEB_UPNP_AV_set ADSL_CFG_LINESTATUS_get ADSL_CUR_LINESTATUS_get ADSL_CFG_LINKTYPE_get ADSL_CUR_LINKTYPE_get ADSL_UP_RATE_get ADSL_DN_RATE_get ADSL_UP_NOISEMARGIN_get ADSL_DN_NOISEMARGIN_get ADSL_UP_ATTEN_get ADSL_DN_ATTEN_get ADSL_NR_OUTPUTPWR_get ADSL_FE_OUTPUTPWR_get ADSL_NR_FAST_FEC_get ADSL_FE_FAST_FEC_get ADSL_NR_INTER_FEC_get ADSL_FE_INTER_FEC_get ADSL_NR_FAST_CRC_get ADSL_FE_FAST_CRC_get ADSL_NR_INTER_CRC_get ADSL_FE_INTER_CRC_get ADSL_NR_LOS_DFT_get ADSL_FE_LOS_DFT_get ADSL_NR_FAST_HEC_get ADSL_FE_FAST_HEC_get ADSL_NR_INTER_HEC_get ADSL_FE_INTER_HEC_get ADSL_NR_ERR_PSEC_get ADSL_FE_ERR_PSEC_get ADSL_REC_CELLS_get ADSL_TX_CELLS_get ADSL_CODE_VER_get ADSL_CFG_OPMODE_get ADSL_CUR_OPMODE_get ADSL_UP_SATTEN_get ADSL_DN_SATTEN_get SNMP_AGENT_get SNMP_AGENT_set SNMP_TRAP_get SNMP_TRAP_set SNMP_COMMUNITYCNT_get SNMP_COMMUNITYCNT_set SNMP_COMMUNITY1_get SNMP_COMMUNITY1_set SNMP_COMMUNITY2_get SNMP_COMMUNITY2_set SNMP_SERVERCNT_get SNMP_SERVERCNT_set SNMP_SERVER1_get SNMP_SERVER1_set NAS_MOUNTED_008_LST_get NAS_SHARED_008_LST_get NAS_SHARED_008_LST_set NAS_USER_004_LIST_get NAS_USER_004_LIST_set NAS_ACCESS_004_LIST_get UMTS_STAUS_get UMTS_STATUS_IP_get UMTS_STATUS_MASK_get UMTS_STATUS_GW_get UMTS_STATUS_DNS_PRI_get UMTS_STATUS_DNS_SEC_get FW_ACCESS_CONTROL_010_LST_get FW_SCHEDULE_NAME_010_LST_get FW_SCHEDULE_010_LST_get DHCP_REV_ITEM_get DHCP_REV_ITEM_set inet_aton memcpy memcmp cfgid_str_table cfgid_str_table_sz cfg_table CFG_set_event _CFG_clean _CFG_commit CFG_save _cfg_del cfg_del_event cfg_str2list ether_aton NULL_Str CFG_str2val parseMarco CFG_set_str_event CFG_val2str mapi_ccfg_commit strtol mapi_ccfg_set mapi_ccfg_get Get_MD5_Str _CFG_unset CFG_id2cfgEntry _CFG_getValue _CFG_setValue __floatsidf __divdf3 mapi_xdsl_cmdctl adslModeString dsl_status dsl_statistics getAdslTypeString stat dhcp_reserved_record mapi_fw_access_control_blksvc_cfg2struct mapi_fw_access_control_user_port_cfg2struct mapi_fw_access_control_blksvc_struct2cfg mapi_lan_cmdctl mapi_sw_cmdctl fseek ftell Osix_malloc Osix_free localtime asctime mapi_wlan_cmdctl strtok strlcpy __extendsfdf2 __muldf3 mapi_nas_cmdctl CFG_set __floatsisf mapi_nat_cmdctl mapi_sys_cmdctl mapi_wan_cmdctl mapi_3g_cmdctl mapi_wan_get_connected_status Osix_GetSysUpTime adsl_util mapi_fw_update_dmz mapi_fw_schedule_start_time_cfg2struct mapi_fw_schedule_end_time_cfg2struct wl_bwctl_util mapi_iptables_cmdctl Osix_send_msg_to_osix_syscmd_service_thread toBypassWanAction mapi_vlan_cmdctl mapi_atm_cmdctl mapi_wlan_update_lan wlan_wsconf_util wlan_util wlan_bwctl_util vlan_util __pack_f libc.so.0 _ftext _fdata _edata __bss_start _fbss _end '9F $R) L$H) @0!&9 (!& $BQ, @ !$ Q$'9 ` !$ ` !$ {$BR ` !$ $BRx ` !$ (!$ !,D ` !$ 8!$BQ @ !$ &$O D !&1 &$O 24BTv gE4B# $ 4Bp 04BF y4BC %4B%b &^4BZQ EZ4B go4B *4BL &4B9B &4Ba" &4B8 &4BK` &4B~ &4B' &4B0 &4B| &4BVe &4B"D &4B# &4BY &4B] &4B~O &4BC &4B~ (!&R F0#$ 0!' @!$H @ !& @ !$ `(!$ `0!$c @(!&1 (!'9 @0!< `0!$c $BU (!$ !r !r @ !$ pH!$ $$h @8!$ *$DU *$DU #0B @ !' !$ !$ @0!(B @8!$ 0!$ 0!$ 0!$ 0!$ 0!$ 0!$ 0!$ 0!$ 0!$ 0!$ 0!$ 0!$ @8!$ @8!$ @(!$ @ !0C @8!$ 8!$ `8!$ (!' `0!' !$ ` !$d '9UD !$S*L $R*4 $Q*@ '9UD @ !$B $B*@ $B*L $B*4 $P*@ $R*L $Q*4 $B*L @ !$ $P*` $B*`$B $U*` #$c*` ff4Bfg0 `0!$ `8!$ P0!(B .4BE #4B ` !$ !'9 .4BE #4B @ !'9 @8!$ @8!$ @!$ @ !$ @!$ @ !$ 0!$ !& 8!$ 8!$ @ !$ 8!$ @ !$ 0!$ @ !& !& ` !$ @0!$ 0!$ `8!$ !$ !$ !$ !$ 8!$ @8!$ @8!$ !0C !0C @(!$ @ !$ \$Q0p &%U &%U &%U &%U &%U @(!< !$C !&ei0 d&ei0 !0C !0B @ !0C @ !0B @8!$ !$ @ !0C @ !0B @8!$ @8!$ @ !' `8!$ !$ /var/run/httpd.pid httpd exit() %x allocate for bypass file list failed %d bytes %s %d %s HTTP/1.0 Server: %s httpd %a, %d %b %Y %H:%M:%S GMT Date: %s Content-Type: %s Cookie: %s Connection: close text/html <HTML><HEAD><TITLE>%d %s</TITLE></HEAD> <BODY BGCOLOR="#cc9999"><H4>%d %s</H4> </BODY></HTML> Not Found File not found. Location: %s ip=%s cannot find ip userinfo[servidx][i].urn=%d matched!!! accept fdopen %d.%d.%d.%d Bad Request No request found. Not Implemented That method is not implemented. Can't parse request. Authorization: Content-Length: boundary= User-Agent: Cookie: post Bad filename. /../ Illegal filename. index.htm urn= Not Found! httpd process %d exit... /www HTTPD: %s(%d) socket setsockopt setsockopt RCVTIMEO bind listen %s:can't bind to any address daemon fork %s(%d): I am child for HTTPD SVR %d %s(%d): Start HTTPD SVR %d httpd normal exit... images/* **.css **.js login*.* top*.* index*.* login_guest.htm login.htm loginerr.htm login_guest_err.htm loginduperr.htm login_guest_ok.htm u132xzp32aai.htm xc324m12sdlo.htm yds32u872vld.htm z983erv3210ba.htm main SET%d SET[%d] %x=[%s] !!!!!!!!!we do reboot=%d Content-Type:text/html <html> <script langugae="javascript"> if('undefined'!=typeof(top.G_prog))top.G_prog=99; if('undefined'!=typeof(top.G_err))top.G_err=%d; </script> </html> Insufficient args '%s' %s %s %d %d %s("%s%d",%u,'%s'); addCfg %s("%s%d",%u,''); %s %s %s("%s",%u,'%s'); %s("%s",%u,''); /usr/sbin/sh_dnld_state_cfg.sh S PASS util_sys_cli bgCmd "/usr/sbin/sh_reboot.sh" cp -f %s %s%s /etc/config/ backup.bin /usr/sbin/sh_cfg_store.sh R %s %s[%d] Command Execution Error: cmd_buf [%s] !!!!!!!!!CGI restore return rc=%d /usr/sbin/sh_dnld_state_cfg.sh S FAIL /usr/sbin/sh_img_upgrade.sh %d %s 0 !!!!!!!!!CGI upgrade rc=%d /usr/sbin/sh_cfg_store.sh B %s %s[%d]: cmd: %s %s timeout from %s %s logout from %s Failed to set log!!! %s login success from %s %s login duplicate from %s %s login error from %s cp /tmp/log_for_tr69 /tmp/%s rm -f /tmp/log_for_tr69 /tmp get key fail Message queue get fail %d Messgae send fail %d %s(%d): fail to send IPC msg to TR69 %s(%d): msg sent ok. /usr/sbin/sh_dnld_state_cfg.sh C /usr/sbin/sh_dnld_state_cfg.sh S IN_PROGRESS Content-Disposition: name="devtag" name="upfile" %s[%d]: Upload Waiting TimeOut!! %s[%d]: Retry_count (Reading with zero length) exceed (%d) times!! result error: %d **.asp **.txt text/plain **.htm **.html **.xml text/xml **.ico image/icon **.css text/css **.gif image/gif **.jpg image/jpeg **.png image/png **.js text/javascript **.bin application/octet-stream **.conf log/log_for_tr69.log log/security_log **.log apply.cgi login.cgi logout.cgi upgrade.cgi restore.cgi cpe/cpe.cgi CFG_MAP CFG_MAP_ARY CFG_GET CFG_ARY CGI_LOGIN_STAT CGI_LOGIN_ESCAPE CGI_LOGIN_ADMIN CGI_LOGIN_MAC CGI_LOGIN_LST CGI_LOGIN_KEEP DSL_CONF DSL_RETRAIN DNS_CONF DDNS_CONF LAN_CONF LAN_DHCP_REV_CONF LAN_DHCP_REV_DEL_CONF SYS_CONF SYS_RESET SYS_MFRESET SYS_BOOT SYS_RMT_MGMT WIFI_CONF WIFI_WEP_CONF WIFI_SSID_CONF WIFI_SSID_SEC WIFI_SSID_QOS_CONF WIFI_ADV_CONF WIFI_MAC_CONF WIFI_WPA_CONF WIFI_WPS_CONF WIFI_WPS_ENROLL_CONF WIFI_WPS_STARTPBC_CONF WIFI_DOT1X_CONF WAN_ATM_CONF WAN_ADSL_ETH_CONF WAN_CONN WAN_DISC NAT_CONF NAT_ADDRMAP NAT_VIRTUALSERVER NAT_APP NTP_CONF WANETH_CONN WANETH_DISC LOG_CLR TR69_CONF FW_CONF FW_FILTER_CONF FW_FILTER_DEL FW_SCHEDULE_CONF FW_SCHEDULE_DEL FW_URL_LIST_CONF FW_URL_LIST_CLEAR FW_MAC_CONF FW_DMZ_CONF FW_SPI_CONF UPNP_CONF QOS_CONF QOS_RULE_CONF QOS_RULE_EDIT_CONF NAS_USER_CONF UMTS_PINCODE_CONF NAS_CONF NAS_BASIC_CONF NAS_USER_DEL_CONF USB_MOUNT_DEL_CONF USB_SHARED_CONF USB_SHARED_DEL_CONF 1,2,3,4,5,6,7,8,9,10,11, 1,2,3,4,5,6,7,8,9,10,11,12,13, 10,11, 10,11,12,13, 1,2,3,4,5,6,7,8,9,10,11,12,13,14, 3,4,5,6,7,8,9, /tmp/ do_cpecgi_post do_restore_cgi do_upload_post do_get_cfg PATH /sbin:/bin:/usr/sbin:/usr/bin waitpid %%%02X MANUF_PHASE manuf phase MGMTACCOUNT_USERNAME mgmtAccount username MGMTACCOUNT_PASSWORD password LAN_NETSECTION netsection LAN_IFNAME ifname LAN_IP4ADDR ip4addr LAN_IP4MASK ip4mask LAN_PROTO proto LAN_DHCP4S_EB dhcp4s_eb LAN_DHCP4POOL_S dhcp4pool_s LAN_DHCP4POOL_E dhcp4pool_e LAN_DHCP4LEASE dhcp4lease LAN_DHCP_VENDOR_OPTION dhcp_vendor_option LAN_DOMAINNAME domainname LAN_DEFAULTROUTE defaultroute LAN_VLAN vlan LAN_DHCP_RESERVED_CLIENT_001 dhcp_reserved_client_001 LAN_DHCP_RESERVED_CLIENT_002 dhcp_reserved_client_002 LAN_DHCP_RESERVED_CLIENT_003 dhcp_reserved_client_003 LAN_DHCP_RESERVED_CLIENT_004 dhcp_reserved_client_004 LAN_DHCP_RESERVED_CLIENT_005 dhcp_reserved_client_005 LAN_DHCP_RESERVED_CLIENT_006 dhcp_reserved_client_006 LAN_DHCP_RESERVED_CLIENT_007 dhcp_reserved_client_007 LAN_DHCP_RESERVED_CLIENT_008 dhcp_reserved_client_008 LAN_DHCP_LOG_100_LST LAN_DHCP_CLIENT_NUM LAN_PORT_STATUS_004_LST LAN_DHCP_REV_024_LST WANCTL_TYPE wanctl WANETH_IFNAME wanETH WANETH_PROTO WANETH_VLAN WANETH_IPASSIGNED ipassigned WANETH_IP4ADDR WANETH_IP4MASK WANETH_IP4GATEWAY ip4gateway WANETH_AUTHPROTOCOL authprotocol WANETH_USERNAME WANETH_PASSWORD WANETH_IDLETIME idletime WANETH_RETRYTIME retrytime WANETH_KEEPALIVETIME keepalivetime WANETH_MTU WANETH_CONNECTTYPE connecttype WANETH_STATIC_DNS static_dns WANETH_PRI_DNS pri_dns WANETH_SEC_DNS sec_dns WANETH_TYPE WANETH_STATUS WANETH_STATUS_MAC STATUS_MAC WANETH_STATUS_IP WANETH_STATUS_MASK STATUS_MASK WANETH_STATUS_GW STATUS_GW WANETH_STATUS_DNS_PRI STATUS_DNS_PRI WANETH_STATUS_DNS_SEC STATUS_DNS_SEC WANETH_STATUS_RATE STATUS_RATE WAN_IFNAME WAN_PROTO WAN_VLAN WAN_IPASSIGNED WAN_IP4ADDR WAN_IP4MASK WAN_IP4GATEWAY WAN_AUTHPROTOCOL WAN_USERNAME WAN_PASSWORD WAN_IDLETIME WAN_RETRYTIME WAN_KEEPALIVETIME WAN_MTU WAN_CONNECTTYPE WAN_STATIC_DNS WAN_PRI_DNS WAN_SEC_DNS WAN_PVC_STATUS_008_LST WAN_PPP_STATUS WAN_PPP_CON_TIME WAN_STATUS_IP SYSTEM_LANG_CODE system lang_code SYSTEM_TIME_ZONE time_zone SYSTEM_GUI_STYLE gui_style SYSTEM_REMOTE_MGMT_EN remote_mgmt_en SYSTEM_REMOTE_MGMT_START_IP remote_mgmt_start_ip SYSTEM_REMOTE_MGMT_END_IP remote_mgmt_end_ip SYSTEM_HOST_NAME host_name SYSTEM_WAN_TYPE wan_type SYSTEM_ACTIVE_WAN_TYPE active_wan_type SYSTEM_PPP_PASS_THRU ppp_pass_thru SYSTEM_DEFAULT_IP default_ip SYSTEM_CCFG_BK_FNAME ccfg_bk_fname SYSTEM_CURRENT_TIME CURRENT_TIME SYSTEM_RUNTIME_CODE_VER RUNTIME_CODE_VER SYSTEM_BOOT_CODE_VER BOOT_CODE_VER SYSTEM_SERIAL_NUM SERIAL_NUM SYSTEM_LAN_MAC_002_LST SYSTEM_WAN_MAC_008_LST WAN_MAC_008_LST SYSTEM_WLAN_MAC_002_LST WLAN_MAC_002_LST SYSTEM_HARDWARE_VER HARDWARE_VER SYSTEM_SECURITY_LOG_100_LST SECURITY_LOG_100_LST DNS_PRI_DNS_SERVER_IP pri_dns_server_ip DNS_PRI_DNS_BIND_TO_IF pri_dns_bind_to_if DNS_SEC_DNS_SERVER_IP sec_dns_server_ip DNS_SEC_DNS_BIND_TO_IF sec_dns_bind_to_if DNS_THIRD_DNS_SERVER_IP third_dns_server_ip DNS_THIRD_DNS_BIND_TO_IF third_dns_bind_to_if WIRELESS_WIRELESS_ENABLE wireless WIRELESS_ENABLE WIRELESS_AP_CHMODE AP_CHMODE WIRELESS_AP_PRIMARY_CH AP_PRIMARY_CH WIRELESS_CTRY_CODE CTRY_CODE WIRELESS_DTIM_PERIOD DTIM_PERIOD WIRELESS_BEACON_INTERVAL BEACON_INTERVAL WIRELESS_FRAG_THRESH FRAG_THRESH WIRELESS_RTS_THRESH RTS_THRESH WIRELESS_WMM_MODE WMM_MODE WIRELESS_WPS_MODE WPS_MODE WIRELESS_WPS_PIN WPS_PIN WIRELESS_WPS_PCB WPS_PCB WIRELESS_POWER_SAVING POWER_SAVING WIRELESS_CHAN_LST CHAN_LST WIRELESS_WPS_STATUS WPS_STATUS WIRELESS_CHANBOND_LST CHANBOND_LST WIRELESS_PWS_TYPE PWS_TYPE WIRELESS_PWS_ENCRTYPE PWS_ENCRTYPE WIRELESS_AP_PIN AP_PIN WIRELESS_SEC_KEY SEC_KEY WIFISSID_AP_SSID wifissid AP_SSID WIFISSID_BSS_ENABLE BSS_ENABLE WIFISSID_MAX_ASSOC MAX_ASSOC WIFISSID_AP_SECMODE AP_SECMODE WIFISSID_AP_CYPHER AP_CYPHER WIFISSID_AP_WPA AP_WPA WIFISSID_AP_WPA_AUTH AP_WPA_AUTH WIFISSID_BROADCAST broadcast WIFISSID_PSK_KEY PSK_KEY WIFISSID_WEP_KEYA WEP_KEYA WIFISSID_WEP_KEYB WEP_KEYB WIFISSID_WEP_KEYC WEP_KEYC WIFISSID_WEP_KEYD WEP_KEYD WIFISSID_AP_PRIMARY_KEY AP_PRIMARY_KEY WIFISSID_VLAN WIFISSID_UP_BW_ENABLE up_bw_enable WIFISSID_DN_BW_ENABLE dn_bw_enable WIFISSID_UPSTREAM_BW upstream_bw WIFISSID_DNSTREAM_BW dnstream_bw WIFISSID_WLAN_STATUS_002_LST WLAN_STATUS_002_LST WIFIMACFILTER_FILTER_ENABLE wifimacfilter FILTER_ENABLE WIFIMACFILTER_FILTER_ACCESS FILTER_ACCESS WIFIMACFILTERADDR_MACFILTER_ADDR wifimacfilteraddr MACFILTER_ADDR DOT1X_CYPHER_SUITE dot1x cypher_suite DOT1X_DOT1XREKEYSECONDS dot1XRekeySeconds DOT1X_DOT1XREKEYPACKETS dot1XRekeyPackets DOT1X_SSNREKEYSECONDS ssnRekeySeconds DOT1X_SSNREKEYPACKETS ssnRekeyPackets DOT1X_DOT1XREKEYING dot1XRekeying DOT1X_SSNREKEYING ssnRekeying DOT1X_STRICTUPDATE strictUpdate DOT1X_ENABLEOS enableOS DOT1X_ENABLEWEP enableWEP DOT1X_ENABLE1X enable1X DOT1X_ENABLEACL enableACL DOT1X_ENABLESSN enableSSN DOT1X_WPA2FLAG wpa2flag DOT1X_ENABLESSNPSK enableSSNPSK DOT1X_SSNPSK256KEYFILED ssnpsk256keyfiled DOT1X_WEPKEYSIZE WEPKeySize DOT1X_DEFAULTKEYID DefaultKeyId DOT1X_SSNPSKASCIIKEY ssnpskASCIIkey DOT1X_SSNPSK256KEY ssnpsk256key DOT1X_SRV_IP srv_ip DOT1X_SECRET_KEY secret_key DOT1X_NAS_ID nas_id DOT1X_SRV_TYPE srv_type DOT1X_SRV_PORT DOT1X_ACC_SRV_PORT acc_srv_port DOT1X_IDLE_SESSION_TIMEOUT idle_session_timeout DOT1X_REAUTHPERIOD reAuthPeriod DOT1X_QUIETPERIOD quietPeriod DOT1X_TXPERIOD txPeriod DOT1X_SUPPTIMEOUT suppTimeout DOT1X_REAUTHCOUNT reAuthCount DOT1X_ENABLE1XAUTHEN enable1Xauthen DOT1X_ROLE role HTTPD_LOGIN_TIMEOUT login_timeout HTTPD_WAIT_TIMEOUT wait_timeout HTTPD_REMOTE_MGNT remote_mgnt HTTPD_HTTP_BROWSE_SERVICE http_browse_service HTTPD_HTTP_BROWSE_PORT http_browse_port TR69_ENABLE tr69 Enable TR69_FIRSTUSEDATE FirstUseDate TR69_URL TR69_USERNAME Username TR69_PASSWORD Password TR69_PERIODICINFORMENABLE PeriodicInformEnable TR69_PERIODICINFORMINTERVAL PeriodicInformInterval TR69_PERIODICINFORMTIME PeriodicInformTime TR69_PARAMETERKEY ParameterKey TR69_COMMANDKEY CommandKey TR69_PROVISIONINGCODE ProvisioningCode TR69_CONNREQURL ConnReqURL TR69_CONNREQUSERNAME ConnReqUsername TR69_CONNREQPASSWORD ConnReqPassword TR69_TR69_M_REBOOT Tr69_m_reboot TR69_TRANSFERFAULTCODE TransferFaultCode TR69_TRANSFERSTARTTIME TransferStartTime TR69_TRANSFERENDTIME TransferEndTime TR69_LOGENABLE LogEnable PVC_NETSECTION PVC_ENCAPS encaps PVC_VPI PVC_VCI PVC_QOS PVC_PCR PVC_SCR PVC_MBS PVC_PVC_LST USB_MAXSUPPORTNUM maxSupportNum USB_ENABLE USB_MAXNUM maxnum DRIVE_NOW_DRIVE_NUM drive_now drive_num DRIVE_NOW_DRIVEINFOA driveinfoa DRIVE_NOW_VOLUMEA volumea DRIVE_NOW_DRIVEINFOB driveinfob DRIVE_NOW_VOLUMEB volumeb PRINTER_NOW_NUM printer_now PRINTER_NOW_MODEL model UMTS_NOW_NUM umts_now UMTS_NOW_MANUFACTURER Manufacturer UMTS_NOW_MODEL SAMBA_HISTORY_DRIVE1 samba_history drive1 SAMBA_HISTORY_DRIVE2 drive2 SAMBA_HISTORY_DRIVE3 drive3 SAMBA_HISTORY_DRIVE4 drive4 SAMBA_HISTORY_DRIVE5 drive5 SAMBA_HISTORY_DRIVE6 drive6 SAMBA_HISTORY_DRIVE7 drive7 SAMBA_HISTORY_DRIVE8 drive8 SAMBA_HISTORY_HISTORY history SAMBA_SHARELIST_DRIVE1 samba_sharelist SAMBA_SHARELIST_DRIVE2 SAMBA_ENABLE samba SAMBA_PRESMBENB preSmbEnb SAMBA_DEF_SMBENABLE def_smbEnable SAMBA_DEF_COMPUTERNAME def_computerName SAMBA_DEF_COMPUTERDESCRIPTION def_computerDescription SAMBA_DEF_GROUPNAME def_groupName SAMBA_DEF_REMOTEENABLE def_remoteEnable SAMBA_SMBENABLE SAMBA_COMPUTERNAME SAMBA_COMPUTERDESCRIPTION SAMBA_GROUPNAME SAMBA_REMOTEENABLE PRINTER_ENABLE printer PRINTER_QUEUENAME queuename UPNP_ENABLE upnp NTP_ENABLE NTP_TZ NTP_INTERVAL interval NTP_SERVERCNT servercnt NTP_SERVER_PRI server_pri NTP_SERVER_SEC server_sec NTP_DLS NTP_YEAR year NTP_MONTH month NTP_DAY NTP_HOUR hour NTP_MINUTE NTP_SECOND second LOG_CATEGORY category QOS_DFT_TOTAL_FWG_NUM qos_dft total_fwg_num QOS_DFT_DFT_FWG dft_fwg QOS_DFT_LNK_NUM lnk_num QOS_DFT_LNK0 lnk0 QOS_DFT_VIF0_0 vif0_0 QOS_DFT_FWG00_0 fwg00_0 QOS_DFT_FWG00_1 fwg00_1 QOS_DFT_FWG00_2 fwg00_2 QOS_DFT_FWG00_3 fwg00_3 QOS_DFT_FWG00_4 fwg00_4 QOS_DFT_FWG00_5 fwg00_5 QOS_DFT_FWG00_6 fwg00_6 QOS_DFT_FWG00_7 fwg00_7 QOS_DFT_CLSFY_SEQ clsfy_seq QOS_DFT_RU00_MAC ru00_mac QOS_DFT_RU00_INIF ru00_inif QOS_DFT_RU00_INPHYIF ru00_inphyif QOS_DFT_RU00_SRCIP ru00_srcip QOS_DFT_RU00_DSTIP ru00_dstip QOS_DFT_RU00_APORPROTO ru00_aporproto QOS_DFT_RU00_SPORT ru00_sport QOS_DFT_RU00_DPORT ru00_dport QOS_DFT_RU00_TOS ru00_tos QOS_DFT_RU00_8021P ru00_8021p QOS_DFT_RU00_ETHTYPE ru00_ethtype QOS_DFT_RU00_PKTLEN ru00_pktlen QOS_DFT_RU00_ACT ru00_act QOS_DFT_RU01_MAC ru01_mac QOS_DFT_RU01_INIF ru01_inif QOS_DFT_RU01_INPHYIF ru01_inphyif QOS_DFT_RU01_SRCIP ru01_srcip QOS_DFT_RU01_DSTIP ru01_dstip QOS_DFT_RU01_APORPROTO ru01_aporproto QOS_DFT_RU01_SPORT ru01_sport QOS_DFT_RU01_DPORT ru01_dport QOS_DFT_RU01_TOS ru01_tos QOS_DFT_RU01_8021P ru01_8021p QOS_DFT_RU01_ETHTYPE ru01_ethtype QOS_DFT_RU01_PKTLEN ru01_pktlen QOS_DFT_RU01_ACT ru01_act PWRSAVE_ENABLE pwrsave PWRSAVE_MAX_PERIOD max_period PWRSAVE_PERIOD1_B period1_b PWRSAVE_PERIOD1_E period1_e PWRSAVE_PERIOD2_B period2_b PWRSAVE_PERIOD2_E period2_e PWRSAVE_PERIOD3_B period3_b PWRSAVE_PERIOD3_E period3_e DDNS_ENABLE ddns DDNS_PROVIDER provider DDNS_USERNAME DDNS_PASSWORD DDNS_HOSTNAME hostname FIREWALL_FIREWALL_ENABLE Firewall firewall_enable FIREWALL_FILTER_ENABLE FIREWALL_MAC_FILTER_ENABLE mac_filter_enable FIREWALL_DMZ_ENABLE dmz_enable FIREWALL_DOS_FUNC dos_func FIREWALL_PINGWAN pingWAN FIREWALL_RIPDEF ripDef FIREWALL_PKT_FRAG_ENABLE pkt_frag_enable FIREWALL_TCP_CONN_ENABLE tcp_conn_enable FIREWALL_UDP_SESSION_ENABLE udp_session_enable FIREWALL_FTP_SRV_ENABLE ftp_srv_enable FIREWALL_H323_SRV_ENABLE h323_srv_enable FIREWALL_TFTP_SRV_ENABLE tftp_srv_enable FIREWALL_SIP_SRV_ENABLE sip_srv_enable FIREWALL_RTSP_SRV_ENABLE rtsp_srv_enable FIREWALL_L2TP_SRV_ENABLE l2tp_srv_enable FIREWALL_PPTP_SRV_ENABLE pptp_srv_enable FIREWALL_IPSEC_SRV_ENABLE ipsec_srv_enable FIREWALL_FRAG_WAIT frag_wait FIREWALL_TCP_SYN_WAIT tcp_syn_wait FIREWALL_TCP_FIN_WAIT tcp_fin_wait FIREWALL_TCP_CONN_IDLE tcp_conn_idle FIREWALL_UDP_SESSION_IDLE udp_session_idle FIREWALL_H323_IDLE h323_idle FIREWALL_DOS_SESSION dos_session FIREWALL_DOS_SESSION_MINUTE dos_session_minute FWACCESSCONTROL_DESCRIPTION FWAccessControl description FWACCESSCONTROL_START_IP FWACCESSCONTROL_END_IP FWACCESSCONTROL_BLOCK_SERVICE block_service FWACCESSCONTROL_USER_PROTOCOL user_protocol FWACCESSCONTROL_USER_PORT user_port FWACCESSCONTROL_SCHEDULE_ID schedule_id FWACCESSCONTROL_AVAIL_IDX FWSCHEDULE_NAME FWSchedule FWSCHEDULE_COMMENT comment FWSCHEDULE_START_TIME start_time FWSCHEDULE_END_TIME end_time FWSCHEDULE_AVAIL_IDX FWMACFILTER_MAC01N FWMACFilter mac01n FWMACFILTER_MAC02N mac02n FWMACFILTER_MAC03N mac03n FWMACFILTER_MAC04N mac04n FWMACFILTER_MAC05N mac05n FWMACFILTER_MAC06N mac06n FWMACFILTER_MAC07N mac07n FWMACFILTER_MAC08N mac08n FWMACFILTER_MAC09N mac09n FWMACFILTER_MAC10N mac10n FWMACFILTER_MAC11N mac11n FWMACFILTER_MAC12N mac12n FWMACFILTER_MAC13N mac13n FWMACFILTER_MAC14N mac14n FWMACFILTER_MAC15N mac15n FWMACFILTER_MAC16N mac16n FWMACFILTER_MAC17N mac17n FWMACFILTER_MAC18N mac18n FWMACFILTER_MAC19N mac19n FWMACFILTER_MAC20N mac20n FWMACFILTER_MAC21N mac21n FWMACFILTER_MAC22N mac22n FWMACFILTER_MAC23N mac23n FWMACFILTER_MAC24N mac24n FWMACFILTER_MAC25N mac25n FWMACFILTER_MAC26N mac26n FWMACFILTER_MAC27N mac27n FWMACFILTER_MAC28N mac28n FWMACFILTER_MAC29N mac29n FWMACFILTER_MAC30N mac30n FWMACFILTER_MAC31N mac31n FWMACFILTER_MAC32N mac32n FWMACFILTER_DHCP_CLIENT_LIST FWURLBLOCKING_URL01N FWURLBlocking url01n FWURLBLOCKING_URL02N url02n FWURLBLOCKING_URL03N url03n FWURLBLOCKING_URL04N url04n FWURLBLOCKING_URL05N url05n FWURLBLOCKING_URL06N url06n FWURLBLOCKING_URL07N url07n FWURLBLOCKING_URL08N url08n FWURLBLOCKING_URL09N url09n FWURLBLOCKING_URL10N url10n FWURLBLOCKING_URL11N url11n FWURLBLOCKING_URL12N url12n FWURLBLOCKING_URL13N url13n FWURLBLOCKING_URL14N url14n FWURLBLOCKING_URL15N url15n FWURLBLOCKING_URL16N url16n FWURLBLOCKING_URL17N url17n FWURLBLOCKING_URL18N url18n FWURLBLOCKING_URL19N url19n FWURLBLOCKING_URL20N url20n FWURLBLOCKING_URL21N url21n FWURLBLOCKING_URL22N url22n FWURLBLOCKING_URL23N url23n FWURLBLOCKING_URL24N url24n FWURLBLOCKING_URL25N url25n FWURLBLOCKING_URL26N url26n FWURLBLOCKING_URL27N url27n FWURLBLOCKING_URL28N url28n FWURLBLOCKING_URL29N url29n FWURLBLOCKING_URL30N url30n FWDMZ_PUBLIC_IP FWDMZ public_ip FWDMZ_CLIENT_IP client_ip NAT_FUNC NAT_MAPPING_254_LST NATADDRESSMAPPING_SRCIP NATAddressMapping srcip NATADDRESSMAPPING_DSTIPB dstipb NATADDRESSMAPPING_DSTIPE dstipe NATSPECIALAPP_GLOBAL_PORT NATSpecialApp Global_Port NATSPECIALAPP_TRIGGER_PORT Trigger_Port NATSPECIALAPP_PPROTOCOL pProtocol NATSPECIALAPP_TPROTOCOL tProtocol NATSPECIALAPP_EFLAG eFlag NATPUBSERV_GLOBAL_PORT NATPubServ NATPUBSERV_PROTOCOL Protocol NATPUBSERV_PRIVATE_IP Private_IP NATPUBSERV_PRIVATE_PORT Private_Port NATPUBSERV_FUNC UPNPD_UPNP_DEFAULT_ENABLE UPNPD upnp_default_enable UPNPD_UPNP_DEFAULT_UPNP_IGD upnp_default_upnp_igd UPNPD_UPNP_ENABLE upnp_enable UPNPD_UPNP_IGD upnp_igd UPNPD_TR64_ENABLE tr64_enable UPNPD_PTR_ENABLE ptr_enable UPNPD_DEBUG_LOG debug_log DLNAS_UPNP_AV DLNAS DLNAS_UPNP_DEFAULT_AV upnp_default_av DLNAS_MUSIC_NUM music_num DLNAS_VIDEO_NUM video_num DLNAS_PICTURE_NUM picture_num DLNAS_DLNA_SCANNING dlna_scanning DLNAS_WEB_UPNP_AV web_upnp_av ADSL_OP_MODE adsl op_mode ADSL_BIT_SWAP_EN bit_swap_en ADSL_SRA_EN SRA_en ADSL_CFG_LINESTATUS CFG_LINESTATUS ADSL_CUR_LINESTATUS CUR_LINESTATUS ADSL_CFG_LINKTYPE CFG_LINKTYPE ADSL_CUR_LINKTYPE CUR_LINKTYPE ADSL_UP_RATE UP_RATE ADSL_DN_RATE DN_RATE ADSL_UP_NOISEMARGIN UP_NOISEMARGIN ADSL_DN_NOISEMARGIN DN_NOISEMARGIN ADSL_UP_ATTEN UP_ATTEN ADSL_DN_ATTEN DN_ATTEN ADSL_NR_OUTPUTPWR NR_OUTPUTPWR ADSL_FE_OUTPUTPWR FE_OUTPUTPWR ADSL_NR_FAST_FEC NR_FAST_FEC ADSL_FE_FAST_FEC FE_FAST_FEC ADSL_NR_INTER_FEC NR_INTER_FEC ADSL_FE_INTER_FEC FE_INTER_FEC ADSL_NR_FAST_CRC NR_FAST_CRC ADSL_FE_FAST_CRC FE_FAST_CRC ADSL_NR_INTER_CRC NR_INTER_CRC ADSL_FE_INTER_CRC FE_INTER_CRC ADSL_NR_LOS_DFT NR_LOS_DFT ADSL_FE_LOS_DFT FE_LOS_DFT ADSL_NR_FAST_HEC NR_FAST_HEC ADSL_FE_FAST_HEC FE_FAST_HEC ADSL_NR_INTER_HEC NR_INTER_HEC ADSL_FE_INTER_HEC FE_INTER_HEC ADSL_NR_ERR_PSEC NR_ERR_PSEC ADSL_FE_ERR_PSEC FE_ERR_PSEC ADSL_REC_CELLS REC_CELLS ADSL_TX_CELLS TX_CELLS ADSL_CODE_VER ADSL_CFG_OPMODE CFG_OPMODE ADSL_CUR_OPMODE CUR_OPMODE ADSL_UP_SATTEN UP_SATTEN ADSL_DN_SATTEN DN_SATTEN SNMP_AGENT snmp agent SNMP_TRAP trap SNMP_COMMUNITYCNT communitycnt SNMP_COMMUNITY1 community1 SNMP_COMMUNITY2 community2 SNMP_SERVERCNT SNMP_SERVER1 server1 QOS_ENABLE QOS_BW_HS bw_hs QOS_BW_HS_MORE bw_hs_more QOS_BW_HR bw_hr QOS_BW_HR_MORE bw_hr_more QOS_BW_H bw_h QOS_BW_H_MORE bw_h_more QOS_BW_M bw_m QOS_BW_M_MORE bw_m_more QOS_BW_N bw_n QOS_BW_N_MORE bw_n_more QOS_BW_L bw_l QOS_BW_L_MORE bw_l_more QOS_BW_LR bw_lr QOS_BW_LR_MORE bw_lr_more QOS_BW_LS bw_ls QOS_BW_LS_MORE bw_ls_more QOS_RULE1N rule1n QOS_RULE2N rule2n QOS_RULE3N rule3n QOS_RULE4N rule4n QOS_RULE5N rule5n QOS_RULE6N rule6n QOS_RULE7N rule7n QOS_RULE8N rule8n QOS_RULE9N rule9n QOS_RULE10N rule10n QOS_RULE11N rule11n QOS_RULE12N rule12n QOS_RULE13N rule13n QOS_RULE14N rule14n QOS_RULE15N rule15n QOS_RULE16N rule16n NAS_FTPD_ENABLE ftpd_enable NAS_FTPD_PORT ftpd_port NAS_SMBD_ENABLE smbd_enable NAS_SMBD_WORKGROUP smbd_workgroup NAS_AUTOSHARE_ENABLE autoshare NAS_SECURITY_ENABLE security NAS_AUTOSHARE_USERNAME autoshare_username NAS_AUTOSHARE_PASSWORD autoshare_password NAS_AUTOSHARE_PRIV autoshare_priv NAS_MOUNTED_008_LST NAS_SHARED_008_LST NAS_USER_004_LIST NAS_ACCESS_004_LIST NASUSERS_USERNAME NASUSERS NASUSERS_PASSWORD NASUSERS_PRIV priv NASSHARES_NAME NASSHARES NASSHARES_PATH path NASSHARES_UUID uuid NASSHARES_USERS users NASSHARES_COMMENT UMTS_FUNC UMTS UMTS_OPERATOR operator UMTS_APN UMTS_PIN_CODE pin_code UMTS_ATD_NO atd_no UMTS_STAUS STAUS UMTS_STATUS_IP UMTS_STATUS_MASK UMTS_STATUS_GW UMTS_STATUS_DNS_PRI UMTS_STATUS_DNS_SEC FW_ACCESS_CONTROL_010_LST ACCESS_CONTROL_010_LST FW_SCHEDULE_NAME_010_LST SCHEDULE_NAME_010_LST FW_SCHEDULE_010_LST SCHEDULE_010_LST DHCP_REV_ITEM DHCP REV_ITEM %s: End CFG_init %s: CFG_set_event: invalid id: %08x %s: CFG_get: Error use list:%08x %s: CFG_get: No cid:%08x %s: cfg_del_event: cid=%08x, rc=%d %s: CFG_get:not found cid:%x %s: len > CFG_MAX_OBJ_SZ Error open profile: %s [%d] Error Set CFG %s = %s Load profile Total: %d %02x%02x %02X:%02X:%02X:%02X:%02X:%02X %04d-%02d-%02d %02d:%02d:%02d %s%d CFG_init cfg_del_event CFG_set_event CFG_get CFG_str2val CFG_val2str %s#%03d %s[%d]: %s@%s (%s) %s[%d]: error to set %s@%s (%s) %s[%d]: error to get %s@%s _CFG_setValue _CFG_getValue none %4.1f %s[%d]Get DSL status fail: %d %s[%d]Get DSL statistics fail: %d %s[%d] get ccfg error !! %s[%d]Get DSL info fail: %d Interleaved Path Fast Path SHOWTIME IDLE TRAINING UNKNOWN Automatic G992.1(G.DMT) G992.3(ADSL2) G992.5(ADSL2+) G992.3(Annex-M) G992.5(Annex-M) NONE AUTO G992.3(Annex-I) G992.3(Annex-L) G992.5(Annex-I) G992.2(G.LITE)T1413 ADSL_CUR_OPMODE_get ADSL_CFG_OPMODE_get ADSL_CODE_VER_get ADSL_CUR_LINESTATUS_get %s_%d /tmp/dhcp_rev_record fopen error %s[%d] get ccfg error!! %s[%d] set ccfg error!! %s[%d] parse ccfg error!! %s[%d] convert ccfg error!! FWACCESSCONTROL_AVAIL_IDX_get FWACCESSCONTROL_USER_PORT_set FWACCESSCONTROL_USER_PORT_get FWACCESSCONTROL_USER_PROTOCOL_set FWACCESSCONTROL_USER_PROTOCOL_get FWACCESSCONTROL_BLOCK_SERVICE_set FWACCESSCONTROL_BLOCK_SERVICE_get %s;%s;%d ['%s','%d'] %s[%d] get invalid ccfg!! %s-%s Always Blocking %d;%s;%s;%s;%s FW_SCHEDULE_010_LST_get FW_SCHEDULE_NAME_010_LST_get FW_ACCESS_CONTROL_010_LST_get lan#001 /tmp/udhcpd.leases%d_%d Failed to get LAN configuration!!! Failed to get UDHCPD lease file!!! Failed to open UDHCPD lease file!!! Incorrect DHCPD lease file content!!! 00:00:00:00:00:00 FWSCHEDULE_AVAIL_IDX_get ['%s','%s','%s','%d'] ETHERNET HALF DOWN FULL ['%d','%s','%d','%s'] lan#%03d dhcp4s_eb Error !! MAPI LAN Obtain Leases File Errrors !! %x:%x:%x:%x:%x:%x ['%s','%s','%s','%s','%d','%d'] dhcp_reserved_client_%03d ['%s'] %s,['%s'] %s;%s;%s;%s;%s NTFS %s;%s;%4.3f GB;%4.3f GB;%d;%s;%s %s[%d]: Failed to get NAT mapping table!!! ['%s','%s','%d','%s','%d','%s','%d'], NAT_MAPPING_254_LST_get ['%d','VC%d','-/-','---','---'] VC MUX Unknown Disable 1483 Bridging PPPOA 1483 Routing PPPOE MAC Encapsulated Routing ['%d','VC%d','%s/%s','%s','%s'] PVC_PVC_LST_get Failed to get log!!! ['%s'] %02X ['%02X-%02X-%02X-%02X-%02X-%02X'] %s-OT (%s) umts %2d day %2d days "%d;%d;%s;%s %2d:%02d:%02d;%d.%03d(KBps);%d.%03d(KBps)" ['%d/%d','%s','%s','%s','%s','%s','%s','%s','%s','%d','%d'] Failed to get connected WAN status! mistyview ADSL eth3 atm0 days %d %s %02d:%02d:%02d %02d:%02d:%02d --:--:-- DISCONNECTED CONNECTED PPPoA PPPoE atm%d 0.0.0.0 /usr/sbin/util_sys_cli addDNSNameServer %d 1 %s /usr/sbin/util_sys_cli addDNSNameServer %d 0 %s /usr/sbin/util_sys_cli clearDNSShadow %d value=%d wan%03d getCurWanPppIface WAN_PVC_STATUS_008_LST_get Failed to get port status!!! 1000 %02x:%02x:%02x:%02x:%02x:%02x DISABLED /bin/bcm_ethctl eth3 linkstate &> /tmp/linkstate4eth3 /tmp/linkstate4eth3 rm -f /tmp/linkstate4eth3 /usr/sbin/util_sys_cli addDNSNameServer 8 1 %s /usr/sbin/util_sys_cli addDNSNameServer 8 0 %s /usr/sbin/util_sys_cli clearDNSShadow 8 TKIP TKIP+AES %s[%d] mapi error !! %s(%s) ['%s','%s','%d, %d','%s','%s','%s'], ['%s','%s','%d','%s','%s','%s'], WPA-WPA2 None WIFISSID_WLAN_STATUS_002_LST_get wps_device_pin '%d','%d','%d','%d' wps_proc_status '%d' '%d', WIRELESS_SEC_KEY_get WIRELESS_PWS_ENCRTYPE_get WIRELESS_PWS_TYPE_get WIRELESS_CHANBOND_LST_get WIRELESS_CHAN_LST_get /usr/sbin/util_sys_cli restartDDNS /usr/sbin/util_sys_cli restartDNS 0 /usr/sbin/util_sys_cli restartDNS 1 /usr/sbin/util_sys_cli restartDNS 2 /usr/sbin/util_sys_cli updateResolvConf %s retrain %s down %s bitswap %s sra %s mode %s %s up . /usr/sbin/sh_xdsl_init.sh CGI_do_DSL_CONF_as Failed to get firewall MAC filter status!!! Failed to update firewall MAC filter!!! Failed to get firewall status!!! Failed to set firewall status!!! %s%02dn Failed to get URL blocking rule!!! Failed to set URL blocking!!! Clear configuration - Firewall URL blocking URL %d: "" URL %d: failed!!! Failed to clear URL blocking!!! Delete configuration - Firewall schedule rule %d Name: "" Name: failed!!! Comment: "" Comment: failed!!! Start time: "" Start time: failed!!! End time: "" End time: failed!!! Failed to delete schedule rule!!! Delete configuration - Firewall access control rule %d Description: "" Description: failed!!! Start IP: "" Start IP: failed!!! End IP: "" End IP: failed!!! Schedule ID: 0 Schedule ID: failed!!! Blocking services: "" Blocking services: failed!!! User defined protocol: "" User defined protocol: failed!!! User defined port: "" User defined port: failed!!! Failed to delete access control rule!!! Failed to get firewall filter status!!! Failed to update firewall filter!!! /usr/sbin/util_lan_cli delRDHCPEntry %d %d /usr/sbin/util_lan_cli config %d /usr/sbin/util_sys_cli restartDNS %d /usr/sbin/util_sys_cli bgCmd "/usr/sbin/util_lan_cli config 0" /usr/sbin/util_sys_cli bgCmd "/usr/sbin/util_lan_cli config 1" /usr/sbin/util_sys_cli bgCmd "/usr/sbin/util_lan_cli config 2" %s(%d): Parsing Error /usr/sbin/util_lan_cli addRDHCPEntry "%s" "%s" "%s" "%s" /usr/sbin/util_lan_cli config %s /usr/sbin/util_sys_cli restartDNS %s CGI_do_LAN_DHCP_REV_CONF_as Failed to clear log!!! Failed to del NAS user(%s)! Failed to restart NAS! Failed to get mounted entries! Failed to del NAS mount-point(%s)! Failed to add NAS user(%s)! Failed to restart NAS service! /usr/sbin/util_sys_cli restartSNTP arc_qos stop arc_qos start %s restart arc_qos bwctl arc_qos bwctl wl . /usr/sbin/sh_upstream_bwalloc.sh . /usr/sbin/sh_wlan_bwctl.sh ./etc/rc.d/S351wlanBwCtl_init %s[%d] %s[%d] Failed to get remote management status!!! cfgIptRmtMgmt.isEnable = %d Failed to get remote management start IP!!! cfgIptRmtMgmt.startIp = %x Failed to get remote management end IP!!! cfgIptRmtMgmt.endIp = %x Failed to set remote management!!! /usr/sbin/sh_cfg_store.sh M /usr/sbin/sh_cfg_store.sh F CGI_do_SYS_BOOT_as CGI_do_SYS_BOOT_ps CGI_do_SYS_MFRESET_as CGI_do_SYS_MFRESET_ps CGI_do_SYS_RESET_as CGI_do_SYS_RESET_ps CGI_do_SYS_CONF_as CGI_do_SYS_CONF_ps %s(%d): Can not get configuration: status!!! sh_tr69_init.sh restart sh_tr69_init.sh stop CGI_do_TR69_CONF_as /usr/sbin/sh_3g_stop.sh /usr/sbin/sh_wan_reinit.sh %s[%d]: UPnP Restart /usr/sbin/util_sys_cli restartUPNPD CGI_do_UPNP_CONF_as %s#001 Failed to disconnect WAN!!! Failed to connect WAN!!! /usr/sbin/util_sys_cli bgCmd "/usr/sbin/sh_wan_reinit.sh" Failed to remove VLAN member!!! Failed to disable WAN interface!!! Failed to set ATM PVC!!! Failed to set WAN interface!!! /usr/sbin/sh_pppd_update_dns.sh %d %s 0.0.0.0 1.1.1.1 Failed to add VLAN member!!! /usr/sbin/util_wan_cli updateQos %s stop %s start %s wpspbc %s wpspin %s %s wl 0 %s wmm %s %s wl 1 %s rmvMbr 1 %s rmvMbr 2 %s rmvMbr 3 %s %s addMbr %s %s . /usr/sbin/sh_wlan_init.sh . /usr/sbin/sh_vlan_init.sh ./etc/rc.d/S350wlan_bringup wl0.1 wl0.2 CGI_do_WIFI_WPS_ENROLL_CONF_as CGI_do_WIFI_SSID_QOS_CONF_as CGI_do_WIFI_SSID_CONF_as Pragma: no-cache Cache-Control: no-cache,no-store,must-revalidate, post-check=0,pre-check=0 Expires: 0 application/x-unknown Content-Disposition: attachment; filename=%s %s%s%06d Bm8 Bmx Bn0 BnX Bnx Bo8 BoX Bo| Bk(,# Ba,0 BaP0 Bg,2 BgL2 Bgp2 We have killed the built-in web server, and launched our own, serving a page which should look like the screenshot attached. Simply browse to: http://192.168.1.1 And you should see: Last edited by unlokia; 02-February-2012 at 15:55. |
#16
|
|||
|
|||
![]()
Orange "Bright Box": a quick overview of the new router, inside *and* out
http://www.youtube.com/watch?v=w6r4VGYO8iY Orange "Bright Box" boot process, captured via USB to serial, using "minicom" (Ubuntu): www.youtube.com/watch?v=yu2GHHCh34I Orange "Bright Box" router: How to change default settings in NVRAM, using "BrightBox" prompt: http://www.youtube.com/watch?v=dgZCM_CFR7I Last edited by unlokia; 02-February-2012 at 14:35. |
#17
|
|||
|
|||
![]()
[updated reply]
Seeing as I now own two of these; one for hacking, one for using, I can tell you that it works wonderfully as a router. One thing I had an issue with, was getting my PC to connect to the 'net, once I had put all the details in. The *router* was definitely connected to ADSL, as it had a WAN IP address. The solution was to turn off the router, reboot the PC, then turn ON the router as the PC reboots. You may not have that issue, but I have outlined what to do, just in case. I've tried playing with the "Bandwidth control" feature; VERY nice. Allows you to throttle downstream *and* upstream bandwidth, when using 3 SSID's (using virtual SSIDs). It doesn't seem to work, but I am sure there is something I have overlooked... Screenshot of "Bandwidth control" page: Last edited by unlokia; 03-February-2012 at 19:58. |
#18
|
|||
|
|||
![]() Okay. I downloaded another version of "busybox" called "busybox-mips" as a temporary hack, so that I have more commands I can run on Bright Box. Here is a better, updated "start_www.sh" script: Code:
#!/bin/sh # simple Bright Box server start script - VERY rough. # check for /ramdisk/www folder existance if [ -d /ramdisk/www ]; then echo "################################" echo "# SERVER ALREADY RUNNING #" echo "# SO WE WILL NOW REBOOT #" echo "# AND RESTORE ORIGINAL WEB UI #" echo "################################" sleep 5 reboot exit else # kill the built-in http server off echo " ### KILLING ORANGE WEB UI ### " killall arc_httpd sleep 1 echo " ### CHANGING ROUTER IP ADDRESS TO: 192.168.1.234 ### " ifconfig br0 192.168.1.234 sleep 1 echo " ### NOW STARTING TELNET ### " telnetd sleep 1 echo " ### NOW STARTING FTP: username="admin" password="x" ### " bftpd -d sleep 1 #make a ramdisk folder for faster running mkdir /ramdisk/www #copy an imageof Bright Box :-) cp ./bbox.jpg /ramdisk/www #create a temporary, basic html page echo "<html><body bgcolor="#FF6600"><h1>This is a test by unlokia</h1><br><h2>busybox-mips</h2><img src="bbox.jpg"></body></html>" > /ramdisk/www/index.html #start our http server ;-) ./busybox-mips httpd -h /ramdisk/www echo "################################" echo "# WEB SERVER IS NOW RUNNING #" echo "# ON: http://192.168.1.234 #" echo "################################" exit fi |
#19
|
|||
|
|||
![]()
questions:
========= 1/ Does anyone here own this router yet (apart from me)? 2/ Does anyone here want to help hack this router, with me? This thread has had almost 1,500 views, and almost no replies. I am not complaining that people are taking an interest, but I would appreciate some help with my investigations, should you wish to do so. SO many views, and so few replies is a little odd... Thanks ![]() |
#20
|
|||
|
|||
![]()
Sup unlokia,
I have one of these routers from Orange, I am most interested in getting a third party or OEM. firmware on the beast. I have no serial interfaces I'm afraid so am approaching the hack purely from a software basis and tracking down an OEM. firmware. ( not so easy as Astoria networks is owned by a web of hardware providers it seems.) And I think you have so many views and little input because this router is so new on the market, give it a month or so and everybody will want a piece of any hacks you find ![]() OK now for links that may or may not be useful too people wanting to know more about this router. https://sviehb.wordpress.com/2011/09...e01-unpacking/ that's a link regarding Astoria firmwares and the how they work and how they may be protected from being reversed, also has a little on who owns Astoria (TLDR: Taiwanese company called Arcadyan). I will add more as more turns up. |
#21
|
|||
|
|||
![]() Sup unlokia, ![]() |
#22
|
|||
|
|||
![]()
Hi guys. Okay, I have found four *hidden* config pages, whilst trawling the firmware
![]() http://192.168.1.1/u132xzp32aai.htm http://192.168.1.1/xc324m12sdlo.htm http://192.168.1.1/yds32u872vld.htm http://192.168.1.1/z983erv3210ba.htm Here are some screenshots, minus my personal data: http://www.flickr.com/photos/2200869...7629246727287/ NOTE: Login *first*, then visit these URLs. If you are logged out and click one, it will just ask you to login, but won't re-direct you to these URLs. Have fun! Last edited by unlokia; 09-February-2012 at 18:49. |
#23
|
|||
|
|||
![]()
Hey Unlokia
looks good, I just got one too, I was looking at Astoria's website but not much there - no new firmware etc. Have you found out how to do static routes.... I don't think it supports it?? |
#24
|
|||
|
|||
![]()
Uhmm, I don't even know what static routes are... haha!
|
#25
|
|||
|
|||
![]()
I also did a port scan on the private side nic, looks like 8085 is open, not sure why though.
|
#26
|
|||
|
|||
![]() I also did a port scan on the private side nic, looks like 8085 is open, not sure why though. ![]() |
#27
|
|||
|
|||
![]()
Good stuff unlokia! Just registered on this forum to say thank you :-) . Some Qs (hope you don't mind) for you . . .
1. Will you be releasing a firmware package - for users like us (who don't have a USB/serial things) who can just flash it to the router and then get all the SSH goodies opened to them? 2. Can a USB printer be connected out of the box to the router and be configured? 3. Have you looked at DD-WRT site - http://www.dd-wrt.com? They seem to be doing a lot of custom builds. Hopefully we can install Twonky on this and get a DLNA server running!! |
#28
|
||||
|
||||
![]()
port 8085, try grep 8085 /etc/services - they might list it there with a name
http://www.dshield.org/port.html?port=8085&exit=1 - doubt much of use but sometimes they will know |
#29
|
|||
|
|||
![]() Hi guys. Okay, I have found four *hidden* config pages, whilst trawling the firmware Hello ![]() Was flicking through your screen shots and saw the remote management bit. These may interest you : MST = Made Simple Technology ACS = Auto-Configuration Server TR-069 is the management protocol see wikipedia and Technical Docs. I don't own one and cant help - but good luck ![]() edit P.S. Just a warning, From the specs it would seam that it informs the ACS if you attempt to alter the ACS settings. Last edited by Memfis; 14-February-2012 at 01:31. Reason: added warning |
#30
|
|||
|
|||
![]()
Gotta say amazing router. Just signed up with orange home broadband and I gotta say how impressed I am with there internet. I live in a area where broadbands speeds are not very good but with orange and this router my internet works very well.
One thing is that I found with the router is that you cant set up port forwarding on different VLANS and I was wondering if anyone here knows of a work around or possible some hacking to change thet ability to port forward to VLAN2 or VLAN3? My other question with this router hacking. As you can connect a 3G dongle to it could I use a Three network dongle as they have all you can eat data plans and the 3g in my area is very good. Would this be practical in the sense that both the adsl and 3g would be running at the same time for everyone in the household? |
![]() |
Tags |
419, adsl, beauty, brightbox, broadband, compare, delay, dhcp, dns, feature, files, firmware, flash, hack, hacking, home, key, line, lock, make, mobile, nat, network, orange, port, product, router, settings, sharing, tools, web, wireless |
Thread Tools | |
Display Modes | |
|
|
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Help!! Weird Router Issue | The Latman | Networking | 17 | 15-January-2011 17:39 |
Staic IP, Port Forward, DMZ | CanineKiller | TalkTalk | 4 | 03-April-2010 09:43 |
Make Your Own Router - secrets revealed | silver | Networking | 356 | 09-February-2010 01:13 |
Valve's Blocks Orange Box Users | MAN WHO | Games | 5 | 07-November-2007 10:54 |