Unlocking BT Home Hub V1 *Upgrade at your own risk*

hi ninj
yes it can be done ....!!

[Dimension]

I have decided to go ahead and use my HHv1 as my wireless modem/router in NZ, however I am going to firstly need to ship it over here! I think I will only need the box and the power for it.

If the DSL cable it longer than 1 metre (I can't remember) then that would be a plus if someone could confirm this. Also, could someone tell me if the USB that comes with it is over a metre long?

Would someone be able to confirm the weight of the items above so that I can work out shipping costs?

Thanks in advance.

[Ben Dover]

Hi Dimension

I've stuck mine on the kitchen scales along with the original box, the Power pack, the USB cable, the DSL cable and two filters .............and it's just over 1100gms I reckon
Looking at the cost of sending a 'small packet' of approx that weight to a Rest of the World destination would be about £12 - £14 I reckon
I also reckon the USB is probably 2m and the DSL is nearer 3m.......thats using the crude method of holding an end in each hand stretching out both my arms to gauge it ( and I'm about 6ft tall )

Hope that helps

[Ben Dover]

Anyway, back to the V1.5

I've tried to restore the amended file and I just appear lose connection with the box, although it doesnt appear to be doing any reloading ?
However if I go to backup again and save the config to the PC once more. I appear to have have lost the entire line that used to have BTHOMEHUB@ etc etc ?
I have also tried telneting into it and, via the menu, trying to alter the PPP settings for the one entry 'internet' ?
I've also tried deleting that one entry and recreating it from scratch
However, whatever way I try it just says unable to set user name

[Dimension]

Hi Dimension

I've stuck mine on the kitchen scales along with the original box, the Power pack, the USB cable, the DSL cable and two filters .............and it's just over 1100gms I reckon
Looking at the cost of sending a 'small packet' of approx that weight to a Rest of the World destination would be about £12 - £14 I reckon
I also reckon the USB is probably 2m and the DSL is nearer 3m.......thats using the crude method of holding an end in each hand stretching out both my arms to gauge it ( and I'm about 6ft tall )

Hope that helps

Originally Posted by Ben Dover

Thankyou very much for your help in this. Much appeciated!

[Quietlife2k]

Hi I'd like to help try modding a HH v1 to something less restricted.

As I understand it the OS for this consists of two parts.
The CFE and the Main OS.
So far the "fix" has been to modify a stock Thompson firmware to make it look like a BT firmware.
Sadly since the CFE & Main OS don't match up we loose DECT.

I'd like to whole flash a Speetouch 790 firmware as it would seem to be identical hardware.
http://wiki.openwrt.org/OpenWrtDocs/...tDocs/Hardware

What I have :
JTAG cable
2x "Donor" Home Hubs
Linux OS

What I *think* I need :
Help performing a whole flash backup.
A full flash copy from an unlocked 790.
Help performing the restore.

Thoughts ?

[Wheel_nut]

Quietlife2k, I am not sure that I understand your proposition. Do you have the TG790 Firmware (or the WRT Firmware compatible with the TG790)?

If you do have this (these), you will probably need to patch the Board Address in the firmware as we did with the ST7G Firmware and then flash it using the Speedtouch utility.

W_n

[Ben Dover]

Hope I'm not drifting this off topic folks

but I was working on a new v2.0 HH and when I restarted it the box appeared to do a factory reset ?
I lost all the settings that I'd changed and the Admin screen went back to the 'change password on first use' page ?
I've not reset it since so any idea how you 'save' changes ?

[Quietlife2k]

Quietlife2k, I am not sure that I understand your proposition. Do you have the TG790 Firmware (or the WRT Firmware compatible with the TG790)?

If you do have this (these), you will probably need to patch the Board Address in the firmware as we did with the ST7G Firmware and then flash it using the Speedtouch utility.

W_n

Originally Posted by Wheel_nut

As I understand it - the firmware changes you refer to only need to be applied in order for the ORIGINAL BT CFE to accept it as being of "BT" origin.

My proposition is to find some helpful person with access to both a JTAG cable and an unlocked TG790 and :

Obtain a FULL flash backup - including the CFE of the TG790 via JTAG.

Write that back to a HH.

See what happens....

I need help with :
Backing up a HH whole flash (in case I need to restore).
Obtaining said TG790 firmware.
Help writing it to a HH.

[dreams_unlimited]

i have a bT home hum and i upgraded to speedtouch 7 a while ago and it perfectly fine. thankx to the users in the scream. my bt hub phone stoped working i am currently on AOL and the home hub works fine on AOL.
my question is dat is there any other upgrade avalible dat i cant use my hub phone and still connect to AOL

[robadams]

Good Luck QuietLife.

Is there any difference between TG790 and 7G?

I found this website in my perusals, the guy that runs it seems quite knowledgeable and contributes to the Whirlpool forum.

http://forums.modem-help.co.uk/viewtopic.php?t=1098

Wish I could help, sure be great to get a full fix.

[Quietlife2k]

I like you am dependent on the web for my info, but if openwrt is accurate - then no - the hardware in the 7G is ever so slightly different :

http://wiki.openwrt.org/OpenWrtDocs/...tDocs/Hardware

It is my understanding that the 7g is based on the Broadcom 6345 whilst the homehub / TG790 is 6348.

I am willing to try a full flash from a 7g if anyone has one - for as long as someone shows me how to backup the homehub first - whilst I have two that I am willing to brick I'd rather not brick them unnecessarily ;-)

once uve done that can u update the hub?

[Quietlife2k]

Ummm kind of.

If I can flash a homehub with a TG790 CFE & firmware then the home hub becomes an IDENTICAL clone of the original TG790.
Since the hardware is the same the CFE matches and it should accept the standard stock Thompson TG790 firmware images, and all features and functions of the new "TGHH790" hybrid should be functional including dect..

There are probably some issues with having identical MAC addresses on two different units so this may only be step one.

7G CFE & firmware however is a different matter.
Without testing I can only guess as to the outcome...
Since the 7G CFE does NOT match the hardware I would expect some or all of the hardware functions to be in some way impared.
Specifically I would expect the same outcome as the modified Thompson firmware has on a standard BT CFE. Namely that dect would continue to be an issue.
It may however allow us to continue using alternative service providers with newer 7G firmware releases without the dect.

This would also have the same potential issues with "cloned" MAC addresses as the TGHH790 solution.

For older (probably out of date) information on CFE :
http://wiki.openwrt.org/OpenWrtDocs/...g/Firmware/CFE

[fruit tool]

i have modified source for hh jtag flasher. dont know if it works under windows.

when you use jtag to read from bthh the bytes in the file get reordered like this
in hex
00 11 22 33
1 2 3 4 normal file

33 22 11 00
4 3 2 1 gets read from flash like this

11 00 33 22
2 1 4 3 has to be written to hh like this

theres a program floating around you can use to rearrange bytes its called
hexmoog
taken from other places:
Assuming you are looking at the bottom of the board
e.g.
http://mikenelis.net/bthomehub/

Then the lowest solder pad is ground. ( lets call this pin 1 ).
pin 2 would be TDI
pin 3 is TDO
pin 5 is TMS
pin 6 is TCK

also
tp32 tdo
tp33 tdi
tp34 tms
tp35 tck

[kazaam]

Is this safe:

I read somewhere

"Basically if the DNS could be edited, and if a 'hacker' was able to gain access to the customer's network, then the your valid DNS could be replaced with a spoof one which re-directed all the customers enquiries, allowing the interception of private traffic e.g. banking information."

I don't know what DNS is, I do not know much about networking, IPs etc..


please help

If i do unlock the hub, will I still be able to use wireless, I have bought a ps3, so would like to go online

Hi there,

I need your advice on a problem i have.
I recently updated successfully my bt home hub to 7g.
However i think there is a problem with the router.
With the ISP provided router (a siemens cl-110) i get around 7 times higher the speed i get with homehub. Any advice on how to fix this problem? (im quite new in the use of routers)
If you need further information on the settings i have please ask. (pppoe vci/vpi 8/35)

@Quietlife2k: 7g uses a Broadcom BCM6348 chip like TG790 as it can be seen here (http://www.jarviser.co.uk/jarviser/images3/inhh_08.jpg) (same chip is used in HH 1.5 http://www.paulbanks.org/projects/homehub/ and apparently HH 1.5 and TG790 use the same PCB as well.)

[bbhs]

I have flashed 2 HH with the 7G and noticed in the web GUI Toolbox screen that the IPP Logo/Image is missing (prin_xl.gif) anybody else had this problem ??
No biggy but just looks bad - thanks

[Wheel_nut]

You can turn on the IPP function via the CLI. You need to Telnet in and then use the ? help facility to drill down through the functions.

I wouldn't bother if I were you .... it's about as useful as a Chocolate Teapot!

[bbhs]

Thanks Wheel_Nut I do not want to really use the function but was just wondering why the prin_xl.gif file was missing from the /image directory.
Just gives the usual explorer missing image default logo.

Hey,

I have read through this thread numerous times now and getting confused. I have been given a bt home hub and bt vision box but do not want to use bt open broadband can it be unlocked and if so what are the simple steps to doing it?

[Scoobs]

The hub can depending on what version the vision box you may as well use it as a door stop as you need BT adsl for that to work.

[kaporwojtas]

Hi guys. I'm new on scream but i can see that you all have done grat piece of job! Is someone can tell me will it work:
I've got Virgin broadband (cabel). Aslko i got netgear wired router connected into it. Recently i've connected bt businnes hub (2wire) as AP - it works fine. What i want to do is connect home hub by wire or wireless to router or AP and set up VOIP on it. Followed javiers guide it should be possible cause he managed to connect voip on hub runned as slave. Does anyone tried it?
Sorry for bad spelling but english is not my main language - hope that someboddy tell me is it wooth to try.

[moog]

Yes I have slaved voip on HH 626, however I also had an additional telephone cable so I could have landline too. You need to set internet connection to LAN on the VOIP Home hub ( http://www.homehubhacks.co.uk/index....outeInternally ), J has collated most of the original posts from here so I would go through his howto. If you do it my way you will need to piggyback the filters for the VOIP hub so it gets only low pass. Good idea to disable software updates too and remote support

[moog]

I have copied up my Home hub utils see http://rapidshare.com/files/197993414/btstuff.rar
Connections.exe show active network connections on HomeHub that still has telnet
HexMoog is hex file viewer with endian reshuffle
shuffle2.exe is the command line endian reshuffle best used via "send to" shell extension, if you dont understand what I mean use HexMoog's tools menu

[kaporwojtas]

THX MOOG.
Ill done that with sipgate!
Now i have milion pounds question: who know how to get SIP settings for vonage? They giving theit own adaptor and tech support said to me that they do not providing SIP settings for any non-vonage devices! Has anyone know how to run vonage on Voip gateway? Uncle google can't sey anything in this matter. Or other a bit offtopic question is:
Wich voip provider giving free landline calls in uk and other EEU countries and incoming phone number? Vonage gives all of this for 15 GBP/Mth.

[Memfis]

I might be wrong but I don't believe vonage runs a SIP service or a SIP gateway to their network.

It's a 'use our stuff or don't use us at all' affair.

my bt homehub got smashed up

Can anyone help with unlocking the Home hub 2.0 and not destroy the wireless signal?

Hi,

I was trying to unlock my BT Homehub, In the process of unlocking, I could run the BT recovery successfully, but when I was doing upgrade, it failed and LED status changed, Power LED RED, Broadband RED (Withouth phone line), Phone Green, Wireless - No Light and Upgrade partial red. Upgrade software is not able to complete as it is finding problem with modem restart.
Does anyone ahve the solution to correct Modem power LED and correct restart?

dks100